Derived class for SX1278 modules. Also used as base class for SX1276, SX1277, SX1279, RFM95 and RFM96. All of these modules use the same basic hardware and only differ in parameter ranges (and names). More...

#include <SX1278.h>

Inheritance diagram for SX1278:

Public Member Functions
	SX1278 (Module *mod)
	Default constructor. Called from Arduino sketch when creating new LoRa instance. More...

int16_t	begin (float freq=434.0, float bw=125.0, uint8_t sf=9, uint8_t cr=7, uint8_t syncWord=RADIOLIB_SX127X_SYNC_WORD, int8_t power=10, uint16_t preambleLength=8, uint8_t gain=0)
	LoRa modem initialization method. Must be called at least once from Arduino sketch to initialize the module. More...

int16_t	beginFSK (float freq=434.0, float br=4.8, float freqDev=5.0, float rxBw=125.0, int8_t power=10, uint16_t preambleLength=16, bool enableOOK=false)
	FSK modem initialization method. Must be called at least once from Arduino sketch to initialize the module. More...

void	reset () override
	Reset method. Will reset the chip to the default state using RST pin.

int16_t	setFrequency (float freq)
	Sets carrier frequency. Allowed values range from 137.0 MHz to 525.0 MHz. More...

int16_t	setBandwidth (float bw)
	Sets LoRa link bandwidth. Allowed values are 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125, 250 and 500 kHz. Only available in LoRa mode. More...

int16_t	setSpreadingFactor (uint8_t sf)
	Sets LoRa link spreading factor. Allowed values range from 6 to 12. Only available in LoRa mode. More...

int16_t	setCodingRate (uint8_t cr)
	Sets LoRa link coding rate denominator. Allowed values range from 5 to 8. Only available in LoRa mode. More...

int16_t	setOutputPower (int8_t power, bool useRfo=false)
	Sets transmission output power. Allowed values range from -3 to 15 dBm (RFO pin) or +2 to +17 dBm (PA_BOOST pin). High power +20 dBm operation is also supported, on the PA_BOOST pin. More...

int16_t	setGain (uint8_t gain)
	Sets gain of receiver LNA (low-noise amplifier). Can be set to any integer in range 1 to 6 where 1 is the highest gain. Set to 0 to enable automatic gain control (recommended). Only available in LoRa mode. More...

int16_t	setDataShaping (uint8_t sh) override
	Sets Gaussian filter bandwidth-time product that will be used for data shaping. Only available in FSK mode with FSK modulation. Allowed values are RADIOLIB_SHAPING_0_3, RADIOLIB_SHAPING_0_5 or RADIOLIB_SHAPING_1_0. Set to RADIOLIB_SHAPING_NONE to disable data shaping. More...

int16_t	setDataShapingOOK (uint8_t sh)
	Sets filter cutoff frequency that will be used for data shaping. Allowed values are 1 for frequency equal to bit rate and 2 for frequency equal to 2x bit rate. Set to 0 to disable data shaping. Only available in FSK mode with OOK modulation. More...

float	getRSSI (bool skipReceive=false)
	Gets recorded signal strength indicator of the latest received packet for LoRa modem, or current RSSI level for FSK modem. More...

int16_t	setCRC (bool enable, bool mode=false)
	Enables/disables CRC check of received packets. More...

int16_t	forceLDRO (bool enable)
	Forces LoRa low data rate optimization. Only available in LoRa mode. After calling this method, LDRO will always be set to the provided value, regardless of symbol length. To re-enable automatic LDRO configuration, call SX1278::autoLDRO() More...

int16_t	autoLDRO ()
	Re-enables automatic LDRO configuration. Only available in LoRa mode. After calling this method, LDRO will be enabled automatically when symbol length exceeds 16 ms. More...

int16_t	implicitHeader (size_t len)
	Set implicit header mode for future reception/transmission. Required for spreading factor 6. More...

int16_t	explicitHeader ()
	Set explicit header mode for future reception/transmission. More...

Public Member Functions inherited from SX127x
	SX127x (Module *mod)
	Default constructor. Called internally when creating new LoRa instance. More...

Module *	getMod ()

int16_t	begin (uint8_t chipVersion, uint8_t syncWord, uint16_t preambleLength)
	Initialization method. Will be called with appropriate parameters when calling initialization method from derived class. More...

int16_t	beginFSK (uint8_t chipVersion, float br, float freqDev, float rxBw, uint16_t preambleLength, bool enableOOK)
	Initialization method for FSK modem. Will be called with appropriate parameters when calling FSK initialization method from derived class. More...

int16_t	transmit (uint8_t *data, size_t len, uint8_t addr=0) override
	Binary transmit method. Will transmit arbitrary binary data up to 255 bytes long using LoRa or up to 63 bytes using FSK modem. For overloads to transmit Arduino String or C-string, see PhysicalLayer::transmit. More...

int16_t	receive (uint8_t *data, size_t len) override
	Binary receive method. Will attempt to receive arbitrary binary data up to 255 bytes long using LoRa or up to 63 bytes using FSK modem. For overloads to receive Arduino String, see PhysicalLayer::receive. More...

int16_t	scanChannel ()
	Performs scan for valid LoRa preamble in the current channel. More...

int16_t	sleep ()
	Sets the LoRa module to sleep to save power. Module will not be able to transmit or receive any data while in sleep mode. Module will wake up automatically when methods like transmit or receive are called. More...

int16_t	standby () override
	Sets the LoRa module to standby. More...

int16_t	transmitDirect (uint32_t frf=0) override
	Enables direct transmission mode on pins DIO1 (clock) and DIO2 (data). While in direct mode, the module will not be able to transmit or receive packets. Can only be activated in FSK mode. More...

int16_t	receiveDirect () override
	Enables direct reception mode on pins DIO1 (clock) and DIO2 (data). While in direct mode, the module will not be able to transmit or receive packets. Can only be activated in FSK mode. More...

int16_t	packetMode ()
	Disables direct mode and enables packet mode, allowing the module to receive packets. Can only be activated in FSK mode. More...

void	setDio0Action (void(*func)(void))
	Set interrupt service routine function to call when DIO0 activates. More...

void	clearDio0Action ()
	Clears interrupt service routine to call when DIO0 activates.

void	setDio1Action (void(*func)(void))
	Set interrupt service routine function to call when DIO1 activates. More...

void	clearDio1Action ()
	Clears interrupt service routine to call when DIO1 activates.

void	setFifoEmptyAction (void(*func)(void))
	Set interrupt service routine function to call when FIFO is empty. More...

void	clearFifoEmptyAction ()
	Clears interrupt service routine to call when FIFO is empty.

void	setFifoFullAction (void(*func)(void))
	Set interrupt service routine function to call when FIFO is full. More...

void	clearFifoFullAction ()
	Clears interrupt service routine to call when FIFO is full.

bool	fifoAdd (uint8_t data, int totalLen, volatile int remLen)
	Set interrupt service routine function to call when FIFO is empty. More...

bool	fifoGet (volatile uint8_t data, int totalLen, volatile int rcvLen)
	Set interrupt service routine function to call when FIFO is sufficently full to read. More...

int16_t	startTransmit (uint8_t *data, size_t len, uint8_t addr=0) override
	Interrupt-driven binary transmit method. Will start transmitting arbitrary binary data up to 255 bytes long using LoRa or up to 63 bytes using FSK modem. More...

int16_t	startReceive (uint8_t len=0, uint8_t mode=RADIOLIB_SX127X_RXCONTINUOUS)
	Interrupt-driven receive method. DIO0 will be activated when full valid packet is received. More...

int16_t	readData (uint8_t *data, size_t len) override
	Reads data that was received after calling startReceive method. This method reads len characters. More...

int16_t	startChannelScan ()
	Interrupt-driven channel activity detection method. DIO0 will be activated when LoRa preamble is detected. DIO1 will be activated if there's no preamble detected before timeout. More...

int16_t	setSyncWord (uint8_t syncWord)
	Sets LoRa sync word. Only available in LoRa mode. More...

int16_t	setCurrentLimit (uint8_t currentLimit)
	Sets current limit for over current protection at transmitter amplifier. Allowed values range from 45 to 120 mA in 5 mA steps and 120 to 240 mA in 10 mA steps. More...

int16_t	setPreambleLength (uint16_t preambleLength)
	Sets LoRa or FSK preamble length. Allowed values range from 6 to 65535 in LoRa mode or 0 to 65535 in FSK mode. More...

float	getFrequencyError (bool autoCorrect=false)
	Gets frequency error of the latest received packet. More...

float	getAFCError ()
	Gets current AFC error. More...

float	getSNR ()
	Gets signal-to-noise ratio of the latest received packet. Only available in LoRa mode. More...

float	getDataRate () const
	Get data rate of the latest transmitted packet. More...

int16_t	setBitRate (float br)
	Sets FSK bit rate. Allowed values range from 1.2 to 300 kbps. Only available in FSK mode. More...

int16_t	setFrequencyDeviation (float freqDev) override
	Sets FSK frequency deviation from carrier frequency. Allowed values depend on bit rate setting and must be lower than 200 kHz. Only available in FSK mode. More...

int16_t	setRxBandwidth (float rxBw)
	Sets FSK receiver bandwidth. Allowed values range from 2.6 to 250 kHz. Only available in FSK mode. More...

int16_t	setAFCBandwidth (float afcBw)
	Sets FSK automatic frequency correction bandwidth. Allowed values range from 2.6 to 250 kHz. Only available in FSK mode. More...

int16_t	setAFC (bool isEnabled)
	Enables or disables FSK automatic frequency correction(AFC) More...

int16_t	setAFCAGCTrigger (uint8_t trigger)
	Controls trigger of AFC and AGC. More...

int16_t	setSyncWord (uint8_t *syncWord, size_t len)
	Sets FSK sync word. Allowed sync words are up to 8 bytes long and can not contain null bytes. Only available in FSK mode. More...

int16_t	setNodeAddress (uint8_t nodeAddr)
	Sets FSK node address. Calling this method will enable address filtering. Only available in FSK mode. More...

int16_t	setBroadcastAddress (uint8_t broadAddr)
	Sets FSK broadcast address. Calling this method will enable address filtering. Only available in FSK mode. More...

int16_t	disableAddressFiltering ()
	Disables FSK address filtering. More...

int16_t	setOOK (bool enableOOK)
	Enables/disables OOK modulation instead of FSK. More...

int16_t	setOokThresholdType (uint8_t type)
	Selects the type of threshold in the OOK data slicer. More...

int16_t	setOokPeakThresholdDecrement (uint8_t value)
	Period of decrement of the RSSI threshold in the OOK demodulator. More...

int16_t	setOokFixedOrFloorThreshold (uint8_t value)
	Fixed threshold for the Data Slicer in OOK mode or floor threshold for the Data Slicer in OOK when Peak mode is used. More...

int16_t	setOokPeakThresholdStep (uint8_t value)
	Size of each decrement of the RSSI threshold in the OOK demodulator. More...

int16_t	enableBitSync ()
	Enable Bit synchronizer. More...

int16_t	disableBitSync ()
	Disable Bit synchronizer (not allowed in Packet mode). More...

size_t	getPacketLength (bool update=true) override
	Query modem for the packet length of received payload. More...

int16_t	fixedPacketLengthMode (uint8_t len=RADIOLIB_SX127X_MAX_PACKET_LENGTH_FSK)
	Set modem in fixed packet length mode. Available in FSK mode only. More...

int16_t	variablePacketLengthMode (uint8_t maxLen=RADIOLIB_SX127X_MAX_PACKET_LENGTH_FSK)
	Set modem in variable packet length mode. Available in FSK mode only. More...

uint32_t	getTimeOnAir (size_t len)
	Get expected time-on-air for a given size of payload. More...

int16_t	setCrcFiltering (bool crcOn=true)
	Enable CRC filtering and generation. More...

int16_t	setRSSIConfig (uint8_t smoothingSamples, int8_t offset=0)
	Sets RSSI measurement configuration in FSK mode. More...

int16_t	setEncoding (uint8_t encoding) override
	Sets transmission encoding. Only available in FSK mode. Allowed values are RADIOLIB_ENCODING_NRZ, RADIOLIB_ENCODING_MANCHESTER and RADIOLIB_ENCODING_WHITENING. More...

uint16_t	getIRQFlags ()
	Reads currently active IRQ flags, can be used to check which event caused an interrupt. In LoRa mode, this is the content of SX127X_REG_IRQ_FLAGS register. In FSK mode, this is the contents of SX127X_REG_IRQ_FLAGS_2 (MSB) and SX127X_REG_IRQ_FLAGS_1 (LSB) registers. More...

uint8_t	getModemStatus ()
	Reads modem status. Only available in LoRa mode. More...

int8_t	getTempRaw ()
	Reads uncalibrated temperature value. This function will change operating mode and should not be called during Tx, Rx or CAD. More...

void	setRfSwitchPins (RADIOLIB_PIN_TYPE rxEn, RADIOLIB_PIN_TYPE txEn)
	Some modules contain external RF switch controlled by two pins. This function gives RadioLib control over those two pins to automatically switch Rx and Tx state. When using automatic RF switch control, DO NOT change the pin mode of rxEn or txEn from Arduino sketch! More...

uint8_t	randomByte ()
	Get one truly random byte from RSSI noise. More...

int16_t	getChipVersion ()
	Read version SPI register. Should return SX1278_CHIP_VERSION (0x12) or SX1272_CHIP_VERSION (0x22) if SX127x is connected and working. More...

int16_t	invertIQ (bool invertIQ)
	Enables/disables Invert the LoRa I and Q signals. More...

void	setDirectAction (void(*func)(void))
	Set interrupt service routine function to call when data bit is receveid in direct mode. More...

void	readBit (RADIOLIB_PIN_TYPE pin)
	Function to read and process data bit in direct reception mode. More...

int16_t	setFHSSHoppingPeriod (uint8_t freqHoppingPeriod)
	Sets the hopping period and enables FHSS. More...

uint8_t	getFHSSHoppingPeriod (void)
	Gets FHSS hopping period. More...

uint8_t	getFHSSChannel (void)
	Gets the FHSS channel in use. More...

void	clearFHSSInt (void)
	Clear the FHSS interrupt.

int16_t	setDIOMapping (RADIOLIB_PIN_TYPE pin, uint8_t value)
	Configure DIO pin mapping to get a given signal on a DIO pin (if available). More...

int16_t	setDIOPreambleDetect (bool usePreambleDetect)
	Configure DIO mapping to use RSSI or Preamble Detect for pins that support it. More...

int16_t	transmit (__FlashStringHelper *fstr, uint8_t addr=0)
	Arduino Flash String transmit method. More...

int16_t	transmit (String &str, uint8_t addr=0)
	Arduino String transmit method. More...

int16_t	transmit (const char *str, uint8_t addr=0)
	C-string transmit method. More...

virtual int16_t	transmit (uint8_t *data, size_t len, uint8_t addr=0)=0
	Binary transmit method. Must be implemented in module class. More...

int16_t	receive (String &str, size_t len=0)
	Arduino String receive method. More...

virtual int16_t	receive (uint8_t *data, size_t len)=0
	Binary receive method. Must be implemented in module class. More...

int16_t	startTransmit (String &str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

int16_t	startTransmit (const char *str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

virtual int16_t	startTransmit (uint8_t *data, size_t len, uint8_t addr=0)=0
	Interrupt-driven binary transmit method. More...

int16_t	readData (String &str, size_t len=0)
	Reads data that was received after calling startReceive method. More...

virtual int16_t	readData (uint8_t *data, size_t len)=0
	Reads data that was received after calling startReceive method. More...

Public Member Functions inherited from PhysicalLayer
	PhysicalLayer (float freqStep, size_t maxPacketLength)
	Default constructor. More...

int16_t	transmit (__FlashStringHelper *fstr, uint8_t addr=0)
	Arduino Flash String transmit method. More...

int16_t	transmit (String &str, uint8_t addr=0)
	Arduino String transmit method. More...

int16_t	transmit (const char *str, uint8_t addr=0)
	C-string transmit method. More...

int16_t	receive (String &str, size_t len=0)
	Arduino String receive method. More...

int16_t	startTransmit (String &str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

int16_t	startTransmit (const char *str, uint8_t addr=0)
	Interrupt-driven Arduino String transmit method. Unlike the standard transmit method, this one is non-blocking. Interrupt pin will be activated when transmission finishes. More...

int16_t	readData (String &str, size_t len=0)
	Reads data that was received after calling startReceive method. More...

float	getFreqStep () const
	Gets the module frequency step size that was set in constructor. More...

int32_t	random (int32_t max)
	Get truly random number in range 0 - max. More...

int32_t	random (int32_t min, int32_t max)
	Get truly random number in range min - max. More...

int16_t	startDirect ()
	Configure module parameters for direct modes. Must be called prior to "ham" modes like RTTY or AX.25. Only available in FSK mode. More...

int16_t	setDirectSyncWord (uint32_t syncWord, uint8_t len)
	Set sync word to be used to determine start of packet in direct reception mode. More...

int16_t	available ()
	Get the number of direct mode bytes currently available in buffer. More...

uint8_t	read ()
	Get data from direct mode buffer. More...

Detailed Description

Derived class for SX1278 modules. Also used as base class for SX1276, SX1277, SX1279, RFM95 and RFM96. All of these modules use the same basic hardware and only differ in parameter ranges (and names).

Constructor & Destructor Documentation

◆ SX1278()

SX1278::SX1278 ( Module * mod )

Default constructor. Called from Arduino sketch when creating new LoRa instance.

Parameters

mod	Instance of Module that will be used to communicate with the LoRa chip.

Member Function Documentation

◆ autoLDRO()

int16_t SX1278::autoLDRO ( )

Re-enables automatic LDRO configuration. Only available in LoRa mode. After calling this method, LDRO will be enabled automatically when symbol length exceeds 16 ms.

Returns: Status Codes

◆ begin()

int16_t SX1278::begin	(	float	freq = `434.0`,
		float	bw = `125.0`,
		uint8_t	sf = `9`,
		uint8_t	cr = `7`,
		uint8_t	syncWord = `RADIOLIB_SX127X_SYNC_WORD`,
		int8_t	power = `10`,
		uint16_t	preambleLength = `8`,
		uint8_t	gain = `0`
	)

LoRa modem initialization method. Must be called at least once from Arduino sketch to initialize the module.

Parameters

freq	Carrier frequency in MHz. Allowed values range from 137.0 MHz to 525.0 MHz.
bw	LoRa link bandwidth in kHz. Allowed values are 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125, 250 and 500 kHz.
sf	LoRa link spreading factor. Allowed values range from 6 to 12.
cr	LoRa link coding rate denominator. Allowed values range from 5 to 8.
syncWord	LoRa sync word. Can be used to distinguish different networks. Note that value 0x34 is reserved for LoRaWAN networks.
power	Transmission output power in dBm. Allowed values range from 2 to 17 dBm.
preambleLength	Length of LoRa transmission preamble in symbols. The actual preamble length is 4.25 symbols longer than the set number. Allowed values range from 6 to 65535.
gain	Gain of receiver LNA (low-noise amplifier). Can be set to any integer in range 1 to 6 where 1 is the highest gain. Set to 0 to enable automatic gain control (recommended).

Returns: Status Codes

◆ beginFSK()

int16_t SX1278::beginFSK	(	float	freq = `434.0`,
		float	br = `4.8`,
		float	freqDev = `5.0`,
		float	rxBw = `125.0`,
		int8_t	power = `10`,
		uint16_t	preambleLength = `16`,
		bool	enableOOK = `false`
	)

FSK modem initialization method. Must be called at least once from Arduino sketch to initialize the module.

Parameters

freq	Carrier frequency in MHz. Allowed values range from 137.0 MHz to 525.0 MHz.
br	Bit rate of the FSK transmission in kbps (kilobits per second). Allowed values range from 1.2 to 300.0 kbps.
freqDev	Frequency deviation of the FSK transmission in kHz. Allowed values range from 0.6 to 200.0 kHz. Note that the allowed range changes based on bit rate setting, so that the condition FreqDev + BitRate/2 <= 250 kHz is always met.
rxBw	Receiver bandwidth in kHz. Allowed values are 2.6, 3.1, 3.9, 5.2, 6.3, 7.8, 10.4, 12.5, 15.6, 20.8, 25, 31.3, 41.7, 50, 62.5, 83.3, 100, 125, 166.7, 200 and 250 kHz.
power	Transmission output power in dBm. Allowed values range from 2 to 17 dBm.
preambleLength	Length of FSK preamble in bits.
enableOOK	Use OOK modulation instead of FSK.

Returns: Status Codes

◆ explicitHeader()

int16_t SX1278::explicitHeader ( )

Set explicit header mode for future reception/transmission.

Returns: Status Codes

◆ forceLDRO()

int16_t SX1278::forceLDRO ( bool enable )

Forces LoRa low data rate optimization. Only available in LoRa mode. After calling this method, LDRO will always be set to the provided value, regardless of symbol length. To re-enable automatic LDRO configuration, call SX1278::autoLDRO()

Parameters

enable Force LDRO to be always enabled (true) or disabled (false).

Returns: Status Codes

◆ getRSSI()

float SX1278::getRSSI ( bool skipReceive = false )

Gets recorded signal strength indicator of the latest received packet for LoRa modem, or current RSSI level for FSK modem.

Parameters

skipReceive Set to true to skip putting radio in receive mode for the RSSI measurement in FKS/OOK mode.

Returns: Last packet RSSI for LoRa modem, or current RSSI level for FSK modem.

◆ implicitHeader()

int16_t SX1278::implicitHeader ( size_t len )

Set implicit header mode for future reception/transmission. Required for spreading factor 6.

Parameters

len	Payload length in bytes.

Returns: Status Codes

◆ setBandwidth()

int16_t SX1278::setBandwidth ( float bw )

Sets LoRa link bandwidth. Allowed values are 10.4, 15.6, 20.8, 31.25, 41.7, 62.5, 125, 250 and 500 kHz. Only available in LoRa mode.

Parameters

bw	LoRa link bandwidth to be set in kHz.

Returns: Status Codes

◆ setCodingRate()

int16_t SX1278::setCodingRate ( uint8_t cr )

Sets LoRa link coding rate denominator. Allowed values range from 5 to 8. Only available in LoRa mode.

Parameters

cr	LoRa link coding rate denominator to be set.

Returns: Status Codes

◆ setCRC()

int16_t SX1278::setCRC	(	bool	enable,
		bool	mode = `false`
	)

Enables/disables CRC check of received packets.

Parameters

enable	Enable (true) or disable (false) CRC.
mode	Set CRC mode to SX127X_CRC_WHITENING_TYPE_CCITT for CCITT, polynomial X16 + X12 + X5 + 1 (false) or SX127X_CRC_WHITENING_TYPE_IBM for IBM, polynomial X16 + X15 + X2 + 1 (true). Only valid in FSK mode.

Returns: Status Codes

◆ setDataShaping()

int16_t SX1278::setDataShaping ( uint8_t sh )

overridevirtual

Sets Gaussian filter bandwidth-time product that will be used for data shaping. Only available in FSK mode with FSK modulation. Allowed values are RADIOLIB_SHAPING_0_3, RADIOLIB_SHAPING_0_5 or RADIOLIB_SHAPING_1_0. Set to RADIOLIB_SHAPING_NONE to disable data shaping.

Parameters

sh	Gaussian shaping bandwidth-time product that will be used for data shaping

Returns: Status Codes

Implements PhysicalLayer.

◆ setDataShapingOOK()

int16_t SX1278::setDataShapingOOK ( uint8_t sh )

Sets filter cutoff frequency that will be used for data shaping. Allowed values are 1 for frequency equal to bit rate and 2 for frequency equal to 2x bit rate. Set to 0 to disable data shaping. Only available in FSK mode with OOK modulation.

Parameters

sh	Cutoff frequency that will be used for data shaping

Returns: Status Codes

◆ setFrequency()

int16_t SX1278::setFrequency ( float freq )

Sets carrier frequency. Allowed values range from 137.0 MHz to 525.0 MHz.

Parameters

freq	Carrier frequency to be set in MHz.

Returns: Status Codes

◆ setGain()

int16_t SX1278::setGain ( uint8_t gain )

Sets gain of receiver LNA (low-noise amplifier). Can be set to any integer in range 1 to 6 where 1 is the highest gain. Set to 0 to enable automatic gain control (recommended). Only available in LoRa mode.

Parameters

gain	Gain of receiver LNA (low-noise amplifier) to be set.

Returns: Status Codes

◆ setOutputPower()

int16_t SX1278::setOutputPower	(	int8_t	power,
		bool	useRfo = `false`
	)

Sets transmission output power. Allowed values range from -3 to 15 dBm (RFO pin) or +2 to +17 dBm (PA_BOOST pin). High power +20 dBm operation is also supported, on the PA_BOOST pin.

Parameters

power	Transmission output power in dBm.
useRfo	Whether to use the RFO (true) or the PA_BOOST (false) pin for the RF output. Defaults to PA_BOOST.

Returns: Status Codes

◆ setSpreadingFactor()

int16_t SX1278::setSpreadingFactor ( uint8_t sf )

Sets LoRa link spreading factor. Allowed values range from 6 to 12. Only available in LoRa mode.

Parameters

sf	LoRa link spreading factor to be set.

Returns: Status Codes

The documentation for this class was generated from the following files:

src/modules/SX127x/SX1278.h
src/modules/SX127x/SX1278.cpp

Public Member Functions

Detailed Description

Constructor & Destructor Documentation

◆ SX1278()

Member Function Documentation

◆ autoLDRO()

◆ begin()

◆ beginFSK()

◆ explicitHeader()

◆ forceLDRO()

◆ getRSSI()

◆ implicitHeader()

◆ setBandwidth()

◆ setCodingRate()

◆ setCRC()

◆ setDataShaping()

◆ setDataShapingOOK()

◆ setFrequency()

◆ setGain()

◆ setOutputPower()

◆ setSpreadingFactor()