diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
old mode 100644
new mode 100644
index e7fae65..af67c1e
--- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
@@ -51,10 +51,21 @@
 	model = "Beelink X2";
 	compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	aliases {
 		serial0 = &uart0;
-		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
-		ethernet1 = &sdiowifi;
+		ethernet0 = &emac;
+		ethernet1 = &rtl8189ftv;
 	};
 
 	chosen {
@@ -100,10 +111,22 @@
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
 
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
@@ -124,6 +147,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
@@ -132,7 +156,7 @@
 	 * Explicitly define the sdio device, so that we can add an ethernet
 	 * alias for it (which e.g. makes u-boot set a mac-address).
 	 */
-	sdiowifi: sdio_wifi@1 {
+	rtl8189ftv: sdio_wifi@1 {
 		reg = <1>;
 	};
 };
@@ -147,10 +171,71 @@
 	status = "okay";
 };
 
+&mmc2_8bit_pins {
+	/* Increase drive strength for DDR modes */
+	drive-strength = <40>;
+	/* eMMC is missing pull-ups */
+	bias-pull-up;
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&mixer0 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
+&sound_hdmi {
+	status = "okay";
+};
+
+&tcon0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
 
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
 &spdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&spdif_tx_pins_a>;
@@ -163,7 +248,14 @@
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	/* USB VBUS is on as long as VCC-IO is on */
 	status = "okay";
 };