RadioLibSmol/src/modules/SX126x/SX126x.cpp

#include "SX126x.h"
#include <string.h>
#include <math.h>
#if !RADIOLIB_EXCLUDE_SX126X

SX126x::SX126x(Module* mod) : PhysicalLayer(RADIOLIB_SX126X_FREQUENCY_STEP_SIZE, RADIOLIB_SX126X_MAX_PACKET_LENGTH) {
  this->mod = mod;
  this->XTAL = false;
  this->standbyXOSC = false;
  this->irqMap[RADIOLIB_IRQ_TX_DONE] = RADIOLIB_SX126X_IRQ_TX_DONE;
  this->irqMap[RADIOLIB_IRQ_RX_DONE] = RADIOLIB_SX126X_IRQ_RX_DONE;
  this->irqMap[RADIOLIB_IRQ_PREAMBLE_DETECTED] = RADIOLIB_SX126X_IRQ_PREAMBLE_DETECTED;
  this->irqMap[RADIOLIB_IRQ_SYNC_WORD_VALID] = RADIOLIB_SX126X_IRQ_SYNC_WORD_VALID;
  this->irqMap[RADIOLIB_IRQ_HEADER_VALID] = RADIOLIB_SX126X_IRQ_HEADER_VALID;
  this->irqMap[RADIOLIB_IRQ_HEADER_ERR] = RADIOLIB_SX126X_IRQ_HEADER_ERR;
  this->irqMap[RADIOLIB_IRQ_CRC_ERR] = RADIOLIB_SX126X_IRQ_CRC_ERR;
  this->irqMap[RADIOLIB_IRQ_CAD_DONE] = RADIOLIB_SX126X_IRQ_CAD_DONE;
  this->irqMap[RADIOLIB_IRQ_CAD_DETECTED] = RADIOLIB_SX126X_IRQ_CAD_DETECTED;
  this->irqMap[RADIOLIB_IRQ_TIMEOUT] = RADIOLIB_SX126X_IRQ_TIMEOUT;
}

int16_t SX126x::begin(uint8_t cr, uint8_t syncWord, uint16_t preambleLength, float tcxoVoltage, bool useRegulatorLDO) {
  // BW in kHz and SF are required in order to calculate LDRO for setModulationParams
  // set the defaults, this will get overwritten later anyway
  this->bandwidthKhz = 500.0;
  this->spreadingFactor = 9;

  // initialize configuration variables (will be overwritten during public settings configuration)
  this->bandwidth = RADIOLIB_SX126X_LORA_BW_500_0;  // initialized to 500 kHz, since lower values will interfere with LLCC68
  this->codingRate = RADIOLIB_SX126X_LORA_CR_4_7;
  this->ldrOptimize = 0x00;
  this->crcTypeLoRa = RADIOLIB_SX126X_LORA_CRC_ON;
  this->preambleLengthLoRa = preambleLength;
  this->tcxoDelay = 0;
  this->headerType = RADIOLIB_SX126X_LORA_HEADER_EXPLICIT;
  this->implicitLen = 0xFF;

  // set module properties and perform initial setup
  int16_t state = this->modSetup(tcxoVoltage, useRegulatorLDO, RADIOLIB_SX126X_PACKET_TYPE_LORA);
  RADIOLIB_ASSERT(state);

  // configure publicly accessible settings
  state = setCodingRate(cr);
  RADIOLIB_ASSERT(state);

  state = setSyncWord(syncWord);
  RADIOLIB_ASSERT(state);

  state = setPreambleLength(preambleLength);
  RADIOLIB_ASSERT(state);

  // set publicly accessible settings that are not a part of begin method
  state = setCurrentLimit(60.0);
  RADIOLIB_ASSERT(state);

  state = setDio2AsRfSwitch(true);
  RADIOLIB_ASSERT(state);

  state = setCRC(2);
  RADIOLIB_ASSERT(state);

  state = invertIQ(false);
  RADIOLIB_ASSERT(state);

  return(state);
}

int16_t SX126x::beginFSK(float br, float freqDev, float rxBw, uint16_t preambleLength, float tcxoVoltage, bool useRegulatorLDO) {
  // initialize configuration variables (will be overwritten during public settings configuration)
  this->bitRate = 21333;                                  // 48.0 kbps
  this->frequencyDev = 52428;                             // 50.0 kHz
  this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_156_2;
  this->rxBandwidthKhz = 156.2;
  this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_5;
  this->crcTypeFSK = RADIOLIB_SX126X_GFSK_CRC_2_BYTE_INV;     // CCITT CRC configuration
  this->preambleLengthFSK = preambleLength;

  // set module properties and perform initial setup
  int16_t state = this->modSetup(tcxoVoltage, useRegulatorLDO, RADIOLIB_SX126X_PACKET_TYPE_GFSK);
  RADIOLIB_ASSERT(state);

  // configure publicly accessible settings
  state = setBitRate(br);
  RADIOLIB_ASSERT(state);

  state = setFrequencyDeviation(freqDev);
  RADIOLIB_ASSERT(state);

  state = setRxBandwidth(rxBw);
  RADIOLIB_ASSERT(state);

  state = setCurrentLimit(60.0);
  RADIOLIB_ASSERT(state);

  state = setPreambleLength(preambleLength);
  RADIOLIB_ASSERT(state);

  // set publicly accessible settings that are not a part of begin method
  uint8_t sync[] = {0x12, 0xAD};
  state = setSyncWord(sync, 2);
  RADIOLIB_ASSERT(state);

  state = setDataShaping(RADIOLIB_SHAPING_NONE);
  RADIOLIB_ASSERT(state);

  state = setEncoding(RADIOLIB_ENCODING_NRZ);
  RADIOLIB_ASSERT(state);

  state = variablePacketLengthMode(RADIOLIB_SX126X_MAX_PACKET_LENGTH);
  RADIOLIB_ASSERT(state);

  state = setCRC(2);
  RADIOLIB_ASSERT(state);

  state = setDio2AsRfSwitch(true);
  RADIOLIB_ASSERT(state);

  return(state);
}

int16_t SX126x::beginLRFHSS(uint8_t bw, uint8_t cr, bool narrowGrid, float tcxoVoltage, bool useRegulatorLDO) {
  this->lrFhssGridNonFcc = narrowGrid;
  
  // set module properties and perform initial setup
  int16_t state = this->modSetup(tcxoVoltage, useRegulatorLDO, RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS);
  RADIOLIB_ASSERT(state);

  // set publicly accessible settings that are not a part of begin method
  state = setCurrentLimit(60.0);
  RADIOLIB_ASSERT(state);

  state = setDio2AsRfSwitch(true);
  RADIOLIB_ASSERT(state);

  // set all packet params to 0 (packet engine is disabled in LR-FHSS mode)
  state = setPacketParamsFSK(0, 0, 0, 0, 0, 0, 0, 0);
  RADIOLIB_ASSERT(state);

  // set bit rate
  this->rxBandwidth = 0;
  this->frequencyDev = 0;
  this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_GAUSS_1;
  state = setBitRate(0.48828125f);
  RADIOLIB_ASSERT(state);

  return(setLrFhssConfig(bw, cr));
}

int16_t SX126x::setLrFhssConfig(uint8_t bw, uint8_t cr, uint8_t hdrCount, uint16_t hopSeqId) {
  // check and cache all parameters
  RADIOLIB_CHECK_RANGE((int8_t)cr, (int8_t)RADIOLIB_SX126X_LR_FHSS_CR_5_6, (int8_t)RADIOLIB_SX126X_LR_FHSS_CR_1_3, RADIOLIB_ERR_INVALID_CODING_RATE);
  this->lrFhssCr = cr;
  RADIOLIB_CHECK_RANGE((int8_t)bw, (int8_t)RADIOLIB_SX126X_LR_FHSS_BW_39_06, (int8_t)RADIOLIB_SX126X_LR_FHSS_BW_1574_2, RADIOLIB_ERR_INVALID_BANDWIDTH);
  this->lrFhssBw = bw;
  RADIOLIB_CHECK_RANGE(hdrCount, 1, 4, RADIOLIB_ERR_INVALID_BIT_RANGE);
  this->lrFhssHdrCount = hdrCount;
  RADIOLIB_CHECK_RANGE((int16_t)hopSeqId, (int16_t)0x000, (int16_t)0x1FF, RADIOLIB_ERR_INVALID_DATA_SHAPING);
  this->lrFhssHopSeqId = hopSeqId;
  return(RADIOLIB_ERR_NONE);
}

int16_t SX126x::reset(bool verify) {
  // run the reset sequence
  this->mod->hal->pinMode(this->mod->getRst(), this->mod->hal->GpioModeOutput);
  this->mod->hal->digitalWrite(this->mod->getRst(), this->mod->hal->GpioLevelLow);
  this->mod->hal->delay(1);
  this->mod->hal->digitalWrite(this->mod->getRst(), this->mod->hal->GpioLevelHigh);

  // return immediately when verification is disabled
  if(!verify) {
    return(RADIOLIB_ERR_NONE);
  }

  // set mode to standby - SX126x often refuses first few commands after reset
  RadioLibTime_t start = this->mod->hal->millis();
  while(true) {
    // try to set mode to standby
    int16_t state = standby();
    if(state == RADIOLIB_ERR_NONE) {
      // standby command successful
      return(RADIOLIB_ERR_NONE);
    }

    // standby command failed, check timeout and try again
    if(this->mod->hal->millis() - start >= 1000) {
      // timed out, possibly incorrect wiring
      return(state);
    }

    // wait a bit to not spam the module
    this->mod->hal->delay(10);
  }
}

int16_t SX126x::transmit(const uint8_t* data, size_t len, uint8_t addr) {
  // set mode to standby
  int16_t state = standby();
  RADIOLIB_ASSERT(state);

  // check packet length
  if(len > RADIOLIB_SX126X_MAX_PACKET_LENGTH) {
    return(RADIOLIB_ERR_PACKET_TOO_LONG);
  }

  // calculate timeout in ms (5ms + 500 % of expected time-on-air)
  RadioLibTime_t timeout = 5 + (getTimeOnAir(len) * 5) / 1000;
  RADIOLIB_DEBUG_BASIC_PRINTLN("Timeout in %lu ms", timeout);

  // start transmission
  state = startTransmit(data, len, addr);
  RADIOLIB_ASSERT(state);

  // wait for packet transmission or timeout
  uint8_t modem = getPacketType();
  RadioLibTime_t start = this->mod->hal->millis();
  while(true) {
    // yield for  multi-threaded platforms
    this->mod->hal->yield();

    // check timeout
    if(this->mod->hal->millis() - start > timeout) {
      finishTransmit();
      return(RADIOLIB_ERR_TX_TIMEOUT);
    }

    // poll the interrupt pin
    if(this->mod->hal->digitalRead(this->mod->getIrq())) {
      // in LoRa or GFSK, only Tx done interrupt is enabled
      if(modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
        break;
      }

      // in LR-FHSS, IRQ signals both Tx done as frequency hop request
      if(this->getIrqFlags() & RADIOLIB_SX126X_IRQ_TX_DONE) {
        break;
      } else {
        // handle frequency hop
        this->setLRFHSSHop(this->lrFhssHopNum % 16);
        clearIrqStatus();
      }
    }
  }

  // update data rate
  RadioLibTime_t elapsed = this->mod->hal->millis() - start;
  this->dataRateMeasured = (len*8.0f)/((float)elapsed/1000.0f);

  return(finishTransmit());
}

int16_t SX126x::receive(uint8_t* data, size_t len) {
  // set mode to standby
  int16_t state = standby();
  RADIOLIB_ASSERT(state);

  RadioLibTime_t timeout = 0;

  // get currently active modem
  uint8_t modem = getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    // calculate timeout (100 LoRa symbols, the default for SX127x series)
    float symbolLength = (float)(uint32_t(1) << this->spreadingFactor) / (float)this->bandwidthKhz;
    timeout = (RadioLibTime_t)(symbolLength * 100.0f);
  
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    // calculate timeout (500 % of expected time-one-air)
    size_t maxLen = len;
    if(len == 0) {
      maxLen = 0xFF;
    }
    float brBps = (RADIOLIB_SX126X_CRYSTAL_FREQ * 1000000.0f * 32.0f) / (float)this->bitRate;
    timeout = (RadioLibTime_t)(((maxLen * 8.0f) / brBps) * 1000.0f * 5.0f);

  } else {
    return(RADIOLIB_ERR_UNKNOWN);
  
  }

  RADIOLIB_DEBUG_BASIC_PRINTLN("Timeout in %lu ms", timeout);

  // start reception
  uint32_t timeoutValue = (uint32_t)(((float)timeout * 1000.0f) / 15.625f);
  state = startReceive(timeoutValue);
  RADIOLIB_ASSERT(state);

  // wait for packet reception or timeout
  bool softTimeout = false;
  RadioLibTime_t start = this->mod->hal->millis();
  while(!this->mod->hal->digitalRead(this->mod->getIrq())) {
    this->mod->hal->yield();
    // safety check, the timeout should be done by the radio
    if(this->mod->hal->millis() - start > timeout) {
      softTimeout = true;
      break;
    }
  }

  // if it was a timeout, this will return an error code
  state = standby();
  if((state != RADIOLIB_ERR_NONE) && (state != RADIOLIB_ERR_SPI_CMD_TIMEOUT)) {
    return(state);
  }

  // check whether this was a timeout or not
  if((getIrqFlags() & RADIOLIB_SX126X_IRQ_TIMEOUT) || softTimeout) {
    standby();
    fixImplicitTimeout();
    clearIrqStatus();
    return(RADIOLIB_ERR_RX_TIMEOUT);
  }

  // fix timeout in implicit LoRa mode
  if(((this->headerType == RADIOLIB_SX126X_LORA_HEADER_IMPLICIT) && (getPacketType() == RADIOLIB_SX126X_PACKET_TYPE_LORA))) {
    state = fixImplicitTimeout();
    RADIOLIB_ASSERT(state);
  }

  // read the received data
  return(readData(data, len));
}

int16_t SX126x::transmitDirect(uint32_t frf) {
  // set RF switch (if present)
  this->mod->setRfSwitchState(this->txMode);

  // user requested to start transmitting immediately (required for RTTY)
  int16_t state = RADIOLIB_ERR_NONE;
  if(frf != 0) {
    state = setRfFrequency(frf);
  }
  RADIOLIB_ASSERT(state);

  // direct mode activation intentionally skipped here, as it seems to lead to much worse results
  uint8_t data[] = { RADIOLIB_SX126X_CMD_NOP };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_TX_CONTINUOUS_WAVE, data, 1));
}

int16_t SX126x::receiveDirect() {
  // set RF switch (if present)
  this->mod->setRfSwitchState(Module::MODE_RX);

  // SX126x is unable to output received data directly
  return(RADIOLIB_ERR_UNKNOWN);
}

int16_t SX126x::directMode() {
  // check modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // set mode to standby
  int16_t state = standby();
  RADIOLIB_ASSERT(state);

  // disable DIO2 RF switch
  state = setDio2AsRfSwitch(false);
  RADIOLIB_ASSERT(state);

  // set DIO2 to clock output and DIO3 to data input
  // this is done exclusively by writing magic values to even more magic registers
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_TX_BITBANG_ENABLE_1, RADIOLIB_SX126X_TX_BITBANG_1_ENABLED, 6, 4);
  RADIOLIB_ASSERT(state);
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_TX_BITBANG_ENABLE_0, RADIOLIB_SX126X_TX_BITBANG_0_ENABLED, 3, 0);
  RADIOLIB_ASSERT(state);
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_DIOX_OUT_ENABLE, RADIOLIB_SX126X_DIO3_OUT_DISABLED, 3, 3);
  RADIOLIB_ASSERT(state);
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_DIOX_IN_ENABLE, RADIOLIB_SX126X_DIO3_IN_ENABLED, 3, 3);
  RADIOLIB_ASSERT(state);

  // enable TxDone interrupt
  state = setDioIrqParams(RADIOLIB_SX126X_IRQ_TX_DONE, RADIOLIB_SX126X_IRQ_TX_DONE);
  RADIOLIB_ASSERT(state);

  // set preamble length to the maximum to prevent SX126x from exiting Tx mode for a while
  state = setPreambleLength(0xFFFF);
  RADIOLIB_ASSERT(state);

  return(state);
}

int16_t SX126x::packetMode() {
  // set mode to standby
  int16_t state = standby();
  RADIOLIB_ASSERT(state);

  // set preamble length to the default
  state = setPreambleLength(16);
  RADIOLIB_ASSERT(state);

  // disable TxDone interrupt
  state = setDioIrqParams(RADIOLIB_SX126X_IRQ_NONE, RADIOLIB_SX126X_IRQ_NONE);
  RADIOLIB_ASSERT(state);

  // restore the magic registers
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_DIOX_IN_ENABLE, RADIOLIB_SX126X_DIO3_IN_DISABLED, 3, 3);
  RADIOLIB_ASSERT(state);
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_DIOX_OUT_ENABLE, RADIOLIB_SX126X_DIO3_OUT_ENABLED, 3, 3);
  RADIOLIB_ASSERT(state);
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_TX_BITBANG_ENABLE_0, RADIOLIB_SX126X_TX_BITBANG_0_DISABLED, 3, 0);
  RADIOLIB_ASSERT(state);
  state = this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_TX_BITBANG_ENABLE_1, RADIOLIB_SX126X_TX_BITBANG_1_DISABLED, 6, 4);
  RADIOLIB_ASSERT(state);

  // enable DIO2 RF switch
  state = setDio2AsRfSwitch(true);
  RADIOLIB_ASSERT(state);

  return(state);
}

int16_t SX126x::scanChannel() {
  ChannelScanConfig_t cfg = {
    .cad = {
      .symNum = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .detPeak = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .detMin = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .exitMode = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .timeout = 0,
      .irqFlags = RADIOLIB_IRQ_CAD_DEFAULT_FLAGS,
      .irqMask = RADIOLIB_IRQ_CAD_DEFAULT_MASK,
    },
  };
  return(this->scanChannel(cfg));
}

int16_t SX126x::scanChannel(const ChannelScanConfig_t &config) {
  // set mode to CAD
  int state = startChannelScan(config);
  RADIOLIB_ASSERT(state);

  // wait for channel activity detected or timeout
  while(!this->mod->hal->digitalRead(this->mod->getIrq())) {
    this->mod->hal->yield();
  }

  // check CAD result
  return(getChannelScanResult());
}

int16_t SX126x::sleep() {
  return(SX126x::sleep(true));
}

int16_t SX126x::sleep(bool retainConfig) {
  // set RF switch (if present)
  this->mod->setRfSwitchState(Module::MODE_IDLE);

  uint8_t sleepMode = RADIOLIB_SX126X_SLEEP_START_WARM | RADIOLIB_SX126X_SLEEP_RTC_OFF;
  if(!retainConfig) {
    sleepMode = RADIOLIB_SX126X_SLEEP_START_COLD | RADIOLIB_SX126X_SLEEP_RTC_OFF;
  }
  int16_t state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_SLEEP, &sleepMode, 1, false, false);

  // wait for SX126x to safely enter sleep mode
  this->mod->hal->delay(1);

  return(state);
}

int16_t SX126x::standby() {
  return(SX126x::standby(this->standbyXOSC ? RADIOLIB_SX126X_STANDBY_XOSC : RADIOLIB_SX126X_STANDBY_RC));
}

int16_t SX126x::standby(uint8_t mode, bool wakeup) {
  // set RF switch (if present)
  this->mod->setRfSwitchState(Module::MODE_IDLE);

  if(wakeup) {
    // send a NOP command - this pulls the NSS low to exit the sleep mode,
    // while preventing interference with possible other SPI transactions
    // see https://github.com/jgromes/RadioLib/discussions/1364
    (void)this->mod->SPIwriteStream((uint16_t)RADIOLIB_SX126X_CMD_NOP, NULL, 0, false, false);
  }

  uint8_t data[] = { mode };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_STANDBY, data, 1));
}

void SX126x::setDio1Action(void (*func)(void)) {
  this->mod->hal->attachInterrupt(this->mod->hal->pinToInterrupt(this->mod->getIrq()), func, this->mod->hal->GpioInterruptRising);
}

void SX126x::clearDio1Action() {
  this->mod->hal->detachInterrupt(this->mod->hal->pinToInterrupt(this->mod->getIrq()));
}

void SX126x::setPacketReceivedAction(void (*func)(void)) {
  this->setDio1Action(func);
}

void SX126x::clearPacketReceivedAction() {
  this->clearDio1Action();
}

void SX126x::setPacketSentAction(void (*func)(void)) {
  this->setDio1Action(func);
}

void SX126x::clearPacketSentAction() {
  this->clearDio1Action();
}

void SX126x::setChannelScanAction(void (*func)(void)) {
  this->setDio1Action(func);
}

void SX126x::clearChannelScanAction() {
  this->clearDio1Action();
}

int16_t SX126x::startTransmit(const uint8_t* data, size_t len, uint8_t addr) {
  (void)addr;
  
  // check packet length
  if(len > RADIOLIB_SX126X_MAX_PACKET_LENGTH) {
    return(RADIOLIB_ERR_PACKET_TOO_LONG);
  }

  // maximum packet length is decreased by 1 when address filtering is active
  if((RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF != RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF) && (len > RADIOLIB_SX126X_MAX_PACKET_LENGTH - 1)) {
    return(RADIOLIB_ERR_PACKET_TOO_LONG);
  }

  // set packet Length
  int16_t state = RADIOLIB_ERR_NONE;
  uint8_t modem = getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    state = setPacketParams(this->preambleLengthLoRa, this->crcTypeLoRa, len, this->headerType, this->invertIQEnabled);
  
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType, len);

  } else if(modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    return(RADIOLIB_ERR_UNKNOWN);
  
  }
  RADIOLIB_ASSERT(state);

  // set DIO mapping
  if(modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    state = setDioIrqParams(RADIOLIB_SX126X_IRQ_TX_DONE | RADIOLIB_SX126X_IRQ_TIMEOUT, RADIOLIB_SX126X_IRQ_TX_DONE);
  } else {
    state = setDioIrqParams(RADIOLIB_SX126X_IRQ_TX_DONE | RADIOLIB_SX126X_IRQ_LR_FHSS_HOP, RADIOLIB_SX126X_IRQ_TX_DONE | RADIOLIB_SX126X_IRQ_LR_FHSS_HOP);
  }
  RADIOLIB_ASSERT(state);

  // set buffer pointers
  state = setBufferBaseAddress();
  RADIOLIB_ASSERT(state);

  // write packet to buffer
  if(modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    state = writeBuffer(const_cast<uint8_t*>(data), len);
  
  } else {
    // first, reset the LR-FHSS state machine
    state = resetLRFHSS();
    RADIOLIB_ASSERT(state);

    // skip hopping for the first 4 - lrFhssHdrCount blocks
    for(int i = 0; i < 4 - this->lrFhssHdrCount; ++i ) {
      stepLRFHSS();
    }

    // in LR-FHSS mode, we need to build the entire packet manually
    uint8_t frame[RADIOLIB_SX126X_MAX_PACKET_LENGTH] = { 0 };
    size_t frameLen = 0;
    this->lrFhssFrameBitsRem = 0;
    this->lrFhssFrameHopsRem = 0;
    this->lrFhssHopNum = 0;
    state = buildLRFHSSPacket(const_cast<uint8_t*>(data), len, frame, &frameLen, &this->lrFhssFrameBitsRem, &this->lrFhssFrameHopsRem);
    RADIOLIB_ASSERT(state);

    // FIXME check max len for FHSS
    state = writeBuffer(frame, frameLen);
    RADIOLIB_ASSERT(state);

    // activate hopping
    uint8_t hopCfg[] = { RADIOLIB_SX126X_HOPPING_ENABLED, (uint8_t)frameLen, (uint8_t)this->lrFhssFrameHopsRem };
    state = writeRegister(RADIOLIB_SX126X_REG_HOPPING_ENABLE, hopCfg, 3);
    RADIOLIB_ASSERT(state);

    // write the initial hopping table
    uint8_t initHops = this->lrFhssFrameHopsRem;
    if(initHops > 16) {
      initHops = 16;
    };
    for(size_t i = 0; i < initHops; i++) {
      // set the hop frequency and symbols
      state = this->setLRFHSSHop(i);
      RADIOLIB_ASSERT(state);
    }
  
  }
  RADIOLIB_ASSERT(state);

  // clear interrupt flags
  state = clearIrqStatus();
  RADIOLIB_ASSERT(state);

  // fix sensitivity
  state = fixSensitivity();
  RADIOLIB_ASSERT(state);

  // set RF switch (if present)
  this->mod->setRfSwitchState(this->txMode);

  // start transmission
  state = setTx(RADIOLIB_SX126X_TX_TIMEOUT_NONE);
  RADIOLIB_ASSERT(state);

  // wait for BUSY to go low (= PA ramp up done)
  while(this->mod->hal->digitalRead(this->mod->getGpio())) {
    this->mod->hal->yield();
  }

  return(state);
}

int16_t SX126x::finishTransmit() {
  // clear interrupt flags
  int16_t state = clearIrqStatus();
  RADIOLIB_ASSERT(state);

  // set mode to standby to disable transmitter/RF switch
  return(standby());
}

int16_t SX126x::startReceive() {
  return(this->startReceive(RADIOLIB_SX126X_RX_TIMEOUT_INF, RADIOLIB_IRQ_RX_DEFAULT_FLAGS, RADIOLIB_IRQ_RX_DEFAULT_MASK, 0));
}

int16_t SX126x::startReceive(uint32_t timeout, RadioLibIrqFlags_t irqFlags, RadioLibIrqFlags_t irqMask, size_t len) {
  // in implicit header mode, use the provided length if it is nonzero
  // otherwise we trust the user has previously set the payload length manually
  if((this->headerType == RADIOLIB_SX126X_LORA_HEADER_IMPLICIT) && (len != 0)) {
    this->implicitLen = len;
  }

  int16_t state = startReceiveCommon(timeout, irqFlags, irqMask);
  RADIOLIB_ASSERT(state);

  // set RF switch (if present)
  this->mod->setRfSwitchState(Module::MODE_RX);

  // set mode to receive
  state = setRx(timeout);

  return(state);
}

int16_t SX126x::startReceiveDutyCycle(uint32_t rxPeriod, uint32_t sleepPeriod, RadioLibIrqFlags_t irqFlags, RadioLibIrqFlags_t irqMask) {
  // datasheet claims time to go to sleep is ~500us, same to wake up, compensate for that with 1 ms + TCXO delay
  uint32_t transitionTime = this->tcxoDelay + 1000;
  sleepPeriod -= transitionTime;

  // divide by 15.625
  uint32_t rxPeriodRaw = (rxPeriod * 8) / 125;
  uint32_t sleepPeriodRaw = (sleepPeriod * 8) / 125;

  // check 24 bit limit and zero value (likely not intended)
  if((rxPeriodRaw & 0xFF000000) || (rxPeriodRaw == 0)) {
    return(RADIOLIB_ERR_INVALID_RX_PERIOD);
  }

  // this check of the high byte also catches underflow when we subtracted transitionTime
  if((sleepPeriodRaw & 0xFF000000) || (sleepPeriodRaw == 0)) {
    return(RADIOLIB_ERR_INVALID_SLEEP_PERIOD);
  }

  int16_t state = startReceiveCommon(RADIOLIB_SX126X_RX_TIMEOUT_INF, irqFlags, irqMask);
  RADIOLIB_ASSERT(state);

  uint8_t data[6] = {(uint8_t)((rxPeriodRaw >> 16) & 0xFF), (uint8_t)((rxPeriodRaw >> 8) & 0xFF), (uint8_t)(rxPeriodRaw & 0xFF),
                     (uint8_t)((sleepPeriodRaw >> 16) & 0xFF), (uint8_t)((sleepPeriodRaw >> 8) & 0xFF), (uint8_t)(sleepPeriodRaw & 0xFF)};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_RX_DUTY_CYCLE, data, 6));
}

int16_t SX126x::startReceiveDutyCycleAuto(uint16_t senderPreambleLength, uint16_t minSymbols, RadioLibIrqFlags_t irqFlags, RadioLibIrqFlags_t irqMask) {
  if(senderPreambleLength == 0) {
    senderPreambleLength = this->preambleLengthLoRa;
  }

  // worst case is that the sender starts transmitting when we're just less than minSymbols from going back to sleep.
  // in this case, we don't catch minSymbols before going to sleep,
  // so we must be awake for at least that long before the sender stops transmitting.
  uint16_t sleepSymbols = senderPreambleLength - 2 * minSymbols;

  // if we're not to sleep at all, just use the standard startReceive.
  if(2 * minSymbols > senderPreambleLength) {
    return(startReceive(RADIOLIB_SX126X_RX_TIMEOUT_INF, irqFlags, irqMask));
  }

  uint32_t symbolLength = ((uint32_t)(10 * 1000) << this->spreadingFactor) / (10 * this->bandwidthKhz);
  uint32_t sleepPeriod = symbolLength * sleepSymbols;
  RADIOLIB_DEBUG_BASIC_PRINTLN("Auto sleep period: %lu", (long unsigned int)sleepPeriod);

  // when the unit detects a preamble, it starts a timer that will timeout if it doesn't receive a header in time.
  // the duration is sleepPeriod + 2 * wakePeriod.
  // The sleepPeriod doesn't take into account shutdown and startup time for the unit (~1ms)
  // We need to ensure that the timeout is longer than senderPreambleLength.
  // So we must satisfy: wakePeriod > (preamblePeriod - (sleepPeriod - 1000)) / 2. (A)
  // we also need to ensure the unit is awake to see at least minSymbols. (B)
  uint32_t wakePeriod = RADIOLIB_MAX(
    (symbolLength * (senderPreambleLength + 1) - (sleepPeriod - 1000)) / 2, // (A)
    symbolLength * (minSymbols + 1)); //(B)
  RADIOLIB_DEBUG_BASIC_PRINTLN("Auto wake period: %lu", (long unsigned int)wakePeriod);

  // If our sleep period is shorter than our transition time, just use the standard startReceive
  if(sleepPeriod < this->tcxoDelay + 1016) {
    return(startReceive(RADIOLIB_SX126X_RX_TIMEOUT_INF, irqFlags, irqMask));
  }

  return(startReceiveDutyCycle(wakePeriod, sleepPeriod, irqFlags, irqMask));
}

int16_t SX126x::startReceiveCommon(uint32_t timeout, RadioLibIrqFlags_t irqFlags, RadioLibIrqFlags_t irqMask) {
  // ensure we are in standby
  int16_t state = standby();
  RADIOLIB_ASSERT(state);

  // set DIO mapping
  if(timeout != RADIOLIB_SX126X_RX_TIMEOUT_INF) {
    irqMask |= (1UL << RADIOLIB_IRQ_TIMEOUT);
  }
  state = setDioIrqParams(getIrqMapped(irqFlags), getIrqMapped(irqMask));
  RADIOLIB_ASSERT(state);

  // set buffer pointers
  state = setBufferBaseAddress();
  RADIOLIB_ASSERT(state);

  // clear interrupt flags
  state = clearIrqStatus();

  // restore original packet length
  uint8_t modem = getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    state = setPacketParams(this->preambleLengthLoRa, this->crcTypeLoRa, this->implicitLen, this->headerType, this->invertIQEnabled);
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType);
  } else {
    return(RADIOLIB_ERR_UNKNOWN);
  }

  return(state);
}

int16_t SX126x::readData(uint8_t* data, size_t len) {
  // this method may get called from receive() after Rx timeout
  // if that's the case, the first call will return "SPI command timeout error"
  // check the IRQ to be sure this really originated from timeout event
  int16_t state = this->mod->SPIcheckStream();
  uint16_t irq = getIrqFlags();
  if((state == RADIOLIB_ERR_SPI_CMD_TIMEOUT) && (irq & RADIOLIB_SX126X_IRQ_TIMEOUT)) {
    // this is definitely Rx timeout
    return(RADIOLIB_ERR_RX_TIMEOUT);
  }
  RADIOLIB_ASSERT(state);

  // check integrity CRC
  int16_t crcState = RADIOLIB_ERR_NONE;
  // Report CRC mismatch when there's a payload CRC error, or a header error and no valid header (to avoid false alarm from previous packet)
  if((irq & RADIOLIB_SX126X_IRQ_CRC_ERR) || ((irq & RADIOLIB_SX126X_IRQ_HEADER_ERR) && !(irq & RADIOLIB_SX126X_IRQ_HEADER_VALID))) {
    crcState = RADIOLIB_ERR_CRC_MISMATCH;
  }
  
  // get packet length and Rx buffer offset
  uint8_t offset = 0;
  size_t length = getPacketLength(true, &offset);
  if((len != 0) && (len < length)) {
    // user requested less data than we got, only return what was requested
    length = len;
  }

  // read packet data starting at offset
  state = readBuffer(data, length, offset);
  RADIOLIB_ASSERT(state);

  // clear interrupt flags
  state = clearIrqStatus();

  // check if CRC failed - this is done after reading data to give user the option to keep them
  RADIOLIB_ASSERT(crcState);

  return(state);
}

int16_t SX126x::startChannelScan() {
  ChannelScanConfig_t cfg = {
    .cad = {
      .symNum = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .detPeak = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .detMin = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .exitMode = RADIOLIB_SX126X_CAD_PARAM_DEFAULT,
      .timeout = 0,
      .irqFlags = RADIOLIB_IRQ_CAD_DEFAULT_FLAGS,
      .irqMask = RADIOLIB_IRQ_CAD_DEFAULT_MASK,
    },
  };
  return(this->startChannelScan(cfg));
}

int16_t SX126x::startChannelScan(const ChannelScanConfig_t &config) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // set mode to standby
  int16_t state = standby();
  RADIOLIB_ASSERT(state);

  // set RF switch (if present)
  this->mod->setRfSwitchState(Module::MODE_RX);

  // set DIO pin mapping
  state = setDioIrqParams(getIrqMapped(config.cad.irqFlags), getIrqMapped(config.cad.irqMask));
  RADIOLIB_ASSERT(state);

  // clear interrupt flags
  state = clearIrqStatus();
  RADIOLIB_ASSERT(state);

  // set mode to CAD
  state = setCad(config.cad.symNum, config.cad.detPeak, config.cad.detMin, config.cad.exitMode, config.cad.timeout);
  return(state);
}

int16_t SX126x::getChannelScanResult() {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // check CAD result
  uint16_t cadResult = getIrqFlags();
  if(cadResult & RADIOLIB_SX126X_IRQ_CAD_DETECTED) {
    // detected some LoRa activity
    return(RADIOLIB_LORA_DETECTED);
  } else if(cadResult & RADIOLIB_SX126X_IRQ_CAD_DONE) {
    // channel is free
    return(RADIOLIB_CHANNEL_FREE);
  }

  return(RADIOLIB_ERR_UNKNOWN);
}

int16_t SX126x::setBandwidth(float bw) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // ensure byte conversion doesn't overflow
  RADIOLIB_CHECK_RANGE(bw, 0.0f, 510.0f, RADIOLIB_ERR_INVALID_BANDWIDTH);

  // check allowed bandwidth values
  uint8_t bw_div2 = bw / 2 + 0.01f;
  switch (bw_div2)  {
    case 3: // 7.8:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_7_8;
      break;
    case 5: // 10.4:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_10_4;
      break;
    case 7: // 15.6:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_15_6;
      break;
    case 10: // 20.8:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_20_8;
      break;
    case 15: // 31.25:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_31_25;
      break;
    case 20: // 41.7:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_41_7;
      break;
    case 31: // 62.5:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_62_5;
      break;
    case 62: // 125.0:
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_125_0;
      break;
    case 125: // 250.0
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_250_0;
      break;
    case 250: // 500.0
      this->bandwidth = RADIOLIB_SX126X_LORA_BW_500_0;
      break;
    default:
      return(RADIOLIB_ERR_INVALID_BANDWIDTH);
  }

  // update modulation parameters
  this->bandwidthKhz = bw;
  return(setModulationParams(this->spreadingFactor, this->bandwidth, this->codingRate, this->ldrOptimize));
}

int16_t SX126x::setSpreadingFactor(uint8_t sf) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  RADIOLIB_CHECK_RANGE(sf, 5, 12, RADIOLIB_ERR_INVALID_SPREADING_FACTOR);

  // update modulation parameters
  this->spreadingFactor = sf;
  return(setModulationParams(this->spreadingFactor, this->bandwidth, this->codingRate, this->ldrOptimize));
}

int16_t SX126x::setCodingRate(uint8_t cr) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  RADIOLIB_CHECK_RANGE(cr, 5, 8, RADIOLIB_ERR_INVALID_CODING_RATE);

  // update modulation parameters
  this->codingRate = cr - 4;
  return(setModulationParams(this->spreadingFactor, this->bandwidth, this->codingRate, this->ldrOptimize));
}

int16_t SX126x::setSyncWord(uint8_t syncWord, uint8_t controlBits) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // update register
  uint8_t data[2] = {(uint8_t)((syncWord & 0xF0) | ((controlBits & 0xF0) >> 4)), (uint8_t)(((syncWord & 0x0F) << 4) | (controlBits & 0x0F))};
  return(writeRegister(RADIOLIB_SX126X_REG_LORA_SYNC_WORD_MSB, data, 2));
}

int16_t SX126x::setCurrentLimit(float currentLimit) {
  // check allowed range
  if(!((currentLimit >= 0) && (currentLimit <= 140))) {
    return(RADIOLIB_ERR_INVALID_CURRENT_LIMIT);
  }

  // calculate raw value
  uint8_t rawLimit = (uint8_t)(currentLimit / 2.5f);

  // update register
  return(writeRegister(RADIOLIB_SX126X_REG_OCP_CONFIGURATION, &rawLimit, 1));
}

float SX126x::getCurrentLimit() {
  // get the raw value
  uint8_t ocp = 0;
  readRegister(RADIOLIB_SX126X_REG_OCP_CONFIGURATION, &ocp, 1);

  // return the actual value
  return((float)ocp * 2.5f);
}

int16_t SX126x::setPreambleLength(size_t preambleLength) {
  uint8_t modem = getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    this->preambleLengthLoRa = preambleLength;
    return(setPacketParams(this->preambleLengthLoRa, this->crcTypeLoRa, this->implicitLen, this->headerType, this->invertIQEnabled));
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    this->preambleLengthFSK = preambleLength;
    // maximum preamble detector length is limited by sync word length
    // for details, see the note in SX1261 datasheet, Rev 2.1, section 6.2.2.1, page 45
    uint8_t maxDetLen = RADIOLIB_MIN(this->syncWordLength, this->preambleLengthFSK);
    this->preambleDetLength = maxDetLen >= 32 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_32 :
                              maxDetLen >= 24 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_24 :
                              maxDetLen >= 16 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_16 :
                              maxDetLen >   0 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_8 :
                              RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_OFF;
    return(setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType));
  }

  return(RADIOLIB_ERR_UNKNOWN);
}

int16_t SX126x::setFrequencyDeviation(float freqDev) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // set frequency deviation to lowest available setting (required for digimodes)
  float newFreqDev = freqDev;
  if(freqDev < 0.0f) {
    newFreqDev = 0.6f;
  }

  RADIOLIB_CHECK_RANGE(newFreqDev, 0.6f, 200.0f, RADIOLIB_ERR_INVALID_FREQUENCY_DEVIATION);

  // calculate raw frequency deviation value
  uint32_t freqDevRaw = (uint32_t)(((newFreqDev * 1000.0f) * (float)((uint32_t)(1) << 25)) / (RADIOLIB_SX126X_CRYSTAL_FREQ * 1000000.0f));

  // check modulation parameters
  this->frequencyDev = freqDevRaw;

  // update modulation parameters
  return(setModulationParamsFSK(this->bitRate, this->pulseShape, this->rxBandwidth, this->frequencyDev));
}

int16_t SX126x::setBitRate(float br) {
  // check active modem
  uint8_t modem = getPacketType();
  if((modem != RADIOLIB_SX126X_PACKET_TYPE_GFSK) && (modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS)) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  if(modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    RADIOLIB_CHECK_RANGE(br, 0.6f, 300.0f, RADIOLIB_ERR_INVALID_BIT_RATE);
  }

  // calculate raw bit rate value
  uint32_t brRaw = (uint32_t)((RADIOLIB_SX126X_CRYSTAL_FREQ * 1000000.0f * 32.0f) / (br * 1000.0f));

  // check modulation parameters
  this->bitRate = brRaw;

  // update modulation parameters
  return(setModulationParamsFSK(this->bitRate, this->pulseShape, this->rxBandwidth, this->frequencyDev));
}

int16_t SX126x::setDataRate(DataRate_t dr) {
  int16_t state = RADIOLIB_ERR_UNKNOWN;

  // select interpretation based on active modem
  uint8_t modem = this->getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    // set the bit rate
    state = this->setBitRate(dr.fsk.bitRate);
    RADIOLIB_ASSERT(state);

    // set the frequency deviation
    state = this->setFrequencyDeviation(dr.fsk.freqDev);

  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    // set the spreading factor
    state = this->setSpreadingFactor(dr.lora.spreadingFactor);
    RADIOLIB_ASSERT(state);

    // set the bandwidth
    state = this->setBandwidth(dr.lora.bandwidth);
    RADIOLIB_ASSERT(state);

    // set the coding rate
    state = this->setCodingRate(dr.lora.codingRate);
  
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    // set the basic config
    state = this->setLrFhssConfig(dr.lrFhss.bw, dr.lrFhss.cr);
    RADIOLIB_ASSERT(state);

    // set hopping grid
    this->lrFhssGridNonFcc = dr.lrFhss.narrowGrid ? RADIOLIB_SX126X_LR_FHSS_GRID_STEP_NON_FCC : RADIOLIB_SX126X_LR_FHSS_GRID_STEP_FCC;

  }

  return(state);
}

int16_t SX126x::checkDataRate(DataRate_t dr) {
  int16_t state = RADIOLIB_ERR_UNKNOWN;

  // select interpretation based on active modem
  uint8_t modem = this->getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    RADIOLIB_CHECK_RANGE(dr.fsk.bitRate, 0.6f, 300.0f, RADIOLIB_ERR_INVALID_BIT_RATE);
    RADIOLIB_CHECK_RANGE(dr.fsk.freqDev, 0.6f, 200.0f, RADIOLIB_ERR_INVALID_FREQUENCY_DEVIATION);
    return(RADIOLIB_ERR_NONE);

  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    RADIOLIB_CHECK_RANGE(dr.lora.spreadingFactor, 5, 12, RADIOLIB_ERR_INVALID_SPREADING_FACTOR);
    RADIOLIB_CHECK_RANGE(dr.lora.bandwidth, 0.0f, 510.0f, RADIOLIB_ERR_INVALID_BANDWIDTH);
    RADIOLIB_CHECK_RANGE(dr.lora.codingRate, 5, 8, RADIOLIB_ERR_INVALID_CODING_RATE);
    return(RADIOLIB_ERR_NONE);
  
  }

  return(state);
}

int16_t SX126x::setRxBandwidth(float rxBw) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // check modulation parameters
  /*if(2 * this->frequencyDev + this->bitRate > rxBw * 1000.0) {
    return(RADIOLIB_ERR_INVALID_MODULATION_PARAMETERS);
  }*/
  this->rxBandwidthKhz = rxBw;

  // check allowed receiver bandwidth values
  if(fabsf(rxBw - 4.8f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_4_8;
  } else if(fabsf(rxBw - 5.8f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_5_8;
  } else if(fabsf(rxBw - 7.3f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_7_3;
  } else if(fabsf(rxBw - 9.7f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_9_7;
  } else if(fabsf(rxBw - 11.7f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_11_7;
  } else if(fabsf(rxBw - 14.6f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_14_6;
  } else if(fabsf(rxBw - 19.5f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_19_5;
  } else if(fabsf(rxBw - 23.4f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_23_4;
  } else if(fabsf(rxBw - 29.3f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_29_3;
  } else if(fabsf(rxBw - 39.0f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_39_0;
  } else if(fabsf(rxBw - 46.9f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_46_9;
  } else if(fabsf(rxBw - 58.6f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_58_6;
  } else if(fabsf(rxBw - 78.2f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_78_2;
  } else if(fabsf(rxBw - 93.8f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_93_8;
  } else if(fabsf(rxBw - 117.3f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_117_3;
  } else if(fabsf(rxBw - 156.2f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_156_2;
  } else if(fabsf(rxBw - 187.2f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_187_2;
  } else if(fabsf(rxBw - 234.3f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_234_3;
  } else if(fabsf(rxBw - 312.0f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_312_0;
  } else if(fabsf(rxBw - 373.6f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_373_6;
  } else if(fabsf(rxBw - 467.0f) <= 0.001f) {
    this->rxBandwidth = RADIOLIB_SX126X_GFSK_RX_BW_467_0;
  } else {
    return(RADIOLIB_ERR_INVALID_RX_BANDWIDTH);
  }

  // update modulation parameters
  return(setModulationParamsFSK(this->bitRate, this->pulseShape, this->rxBandwidth, this->frequencyDev));
}

int16_t SX126x::setRxBoostedGainMode(bool rxbgm, bool persist) {
  // update RX gain setting register
  uint8_t rxGain = rxbgm ? RADIOLIB_SX126X_RX_GAIN_BOOSTED : RADIOLIB_SX126X_RX_GAIN_POWER_SAVING;
  int16_t state = writeRegister(RADIOLIB_SX126X_REG_RX_GAIN, &rxGain, 1);
  RADIOLIB_ASSERT(state);

  // add Rx Gain register to retention memory if requested
  if(persist) {
    // values and registers below are specified in SX126x datasheet v2.1 section 9.6, just below table 9-3
    uint8_t data[] = { 0x01, (uint8_t)((RADIOLIB_SX126X_REG_RX_GAIN >> 8) & 0xFF), (uint8_t)(RADIOLIB_SX126X_REG_RX_GAIN & 0xFF) };
    state = writeRegister(RADIOLIB_SX126X_REG_RX_GAIN_RETENTION_0, data, 3);
  }

  return(state);
}

int16_t SX126x::setDataShaping(uint8_t sh) {
  // check active modem
  uint8_t modem = getPacketType();
  if((modem != RADIOLIB_SX126X_PACKET_TYPE_GFSK) && (modem != RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS)) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // set data shaping
  switch(sh) {
    case RADIOLIB_SHAPING_NONE:
      this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_NONE;
      break;
    case RADIOLIB_SHAPING_0_3:
      this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_3;
      break;
    case RADIOLIB_SHAPING_0_5:
      this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_5;
      break;
    case RADIOLIB_SHAPING_0_7:
      this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_GAUSS_0_7;
      break;
    case RADIOLIB_SHAPING_1_0:
      this->pulseShape = RADIOLIB_SX126X_GFSK_FILTER_GAUSS_1;
      break;
    default:
      return(RADIOLIB_ERR_INVALID_DATA_SHAPING);
  }

  // update modulation parameters
  return(setModulationParamsFSK(this->bitRate, this->pulseShape, this->rxBandwidth, this->frequencyDev));
}

int16_t SX126x::setSyncWord(uint8_t* syncWord, size_t len) {
  // check active modem
  uint8_t modem = getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    // check sync word Length
    if(len > 8) {
      return(RADIOLIB_ERR_INVALID_SYNC_WORD);
    }

    // write sync word
    int16_t state = writeRegister(RADIOLIB_SX126X_REG_SYNC_WORD_0, syncWord, len);
    RADIOLIB_ASSERT(state);

    // update packet parameters
    this->syncWordLength = len * 8;
    
    // maximum preamble detector length is limited by sync word length
    // for details, see the note in SX1261 datasheet, Rev 2.1, section 6.2.2.1, page 45
    uint8_t maxDetLen = RADIOLIB_MIN(this->syncWordLength, this->preambleLengthFSK);
    this->preambleDetLength = maxDetLen >= 32 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_32 :
                              maxDetLen >= 24 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_24 :
                              maxDetLen >= 16 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_16 :
                              maxDetLen >   0 ? RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_8 :
                              RADIOLIB_SX126X_GFSK_PREAMBLE_DETECT_OFF;
    state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType);

    return(state);
  
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    // with length set to 1 and LoRa modem active, assume it is the LoRa sync word
    if(len > 1) {
      return(RADIOLIB_ERR_INVALID_SYNC_WORD);
    }
    return(setSyncWord(syncWord[0]));

  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    // with length set to 4 and LR-FHSS modem active, assume it is the LR-FHSS sync word
    if(len != sizeof(uint32_t)) {
      return(RADIOLIB_ERR_INVALID_SYNC_WORD);
    }
    memcpy(this->lrFhssSyncWord, syncWord, sizeof(uint32_t));
  
  }

  return(RADIOLIB_ERR_WRONG_MODEM);
}

int16_t SX126x::setSyncBits(uint8_t *syncWord, uint8_t bitsLen) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // check sync word Length
  if(bitsLen > 0x40) {
    return(RADIOLIB_ERR_INVALID_SYNC_WORD);
  }

  uint8_t bytesLen = bitsLen / 8;
  if ((bitsLen % 8) != 0) {
    bytesLen++;
  }

  return(setSyncWord(syncWord, bytesLen));
}

int16_t SX126x::setCRC(uint8_t len, uint16_t initial, uint16_t polynomial, bool inverted) {
  // check active modem
  uint8_t modem = getPacketType();

  if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    // update packet parameters
    switch(len) {
      case 0:
        this->crcTypeFSK = RADIOLIB_SX126X_GFSK_CRC_OFF;
        break;
      case 1:
        if(inverted) {
          this->crcTypeFSK = RADIOLIB_SX126X_GFSK_CRC_1_BYTE_INV;
        } else {
          this->crcTypeFSK = RADIOLIB_SX126X_GFSK_CRC_1_BYTE;
        }
        break;
      case 2:
        if(inverted) {
          this->crcTypeFSK = RADIOLIB_SX126X_GFSK_CRC_2_BYTE_INV;
        } else {
          this->crcTypeFSK = RADIOLIB_SX126X_GFSK_CRC_2_BYTE;
        }
        break;
      default:
        return(RADIOLIB_ERR_INVALID_CRC_CONFIGURATION);
    }

    int16_t state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType);
    RADIOLIB_ASSERT(state);

    // write initial CRC value
    uint8_t data[2] = {(uint8_t)((initial >> 8) & 0xFF), (uint8_t)(initial & 0xFF)};
    state = writeRegister(RADIOLIB_SX126X_REG_CRC_INITIAL_MSB, data, 2);
    RADIOLIB_ASSERT(state);

    // write CRC polynomial value
    data[0] = (uint8_t)((polynomial >> 8) & 0xFF);
    data[1] = (uint8_t)(polynomial & 0xFF);
    state = writeRegister(RADIOLIB_SX126X_REG_CRC_POLYNOMIAL_MSB, data, 2);

    return(state);

  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    // LoRa CRC doesn't allow to set CRC polynomial, initial value, or inversion

    // update packet parameters
    if(len) {
      this->crcTypeLoRa = RADIOLIB_SX126X_LORA_CRC_ON;
    } else {
      this->crcTypeLoRa = RADIOLIB_SX126X_LORA_CRC_OFF;
    }

    return(setPacketParams(this->preambleLengthLoRa, this->crcTypeLoRa, this->implicitLen, this->headerType, this->invertIQEnabled));
  }

  return(RADIOLIB_ERR_UNKNOWN);
}

int16_t SX126x::setWhitening(bool enabled, uint16_t initial) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  int16_t state = RADIOLIB_ERR_NONE;
  if(!enabled) {
    // disable whitening
    this->whitening = RADIOLIB_SX126X_GFSK_WHITENING_OFF;

    state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType);
    RADIOLIB_ASSERT(state);

  } else {
    // enable whitening
    this->whitening = RADIOLIB_SX126X_GFSK_WHITENING_ON;

    // write initial whitening value
    // as per note on pg. 65 of datasheet v1.2: "The user should not change the value of the 7 MSB's of this register"
    uint8_t data[2];
    // first read the actual value and mask 7 MSB which we can not change
    // if different value is written in 7 MSB, the Rx won't even work (tested on HW)
    state = readRegister(RADIOLIB_SX126X_REG_WHITENING_INITIAL_MSB, data, 1);
    RADIOLIB_ASSERT(state);

    data[0] = (data[0] & 0xFE) | (uint8_t)((initial >> 8) & 0x01);
    data[1] = (uint8_t)(initial & 0xFF);
    state = writeRegister(RADIOLIB_SX126X_REG_WHITENING_INITIAL_MSB, data, 2);
    RADIOLIB_ASSERT(state);

    state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, this->packetType);
    RADIOLIB_ASSERT(state);
  }
  return(state);
}

float SX126x::getDataRate() const {
  return(this->dataRateMeasured);
}

float SX126x::getRSSI() {
  return(this->getRSSI(true));
}

float SX126x::getRSSI(bool packet) {
  if(packet) { 
    // get last packet RSSI from packet status
    uint32_t packetStatus = getPacketStatus();
    uint8_t rssiPkt = packetStatus & 0xFF;
    return(-1.0 * rssiPkt/2.0);
  } else {
    // get instantaneous RSSI value
    uint8_t rssiRaw = 0;
    this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_RSSI_INST, &rssiRaw, 1);
    return((float)rssiRaw / (-2.0f));
  }
}

float SX126x::getSNR() {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // get last packet SNR from packet status
  uint32_t packetStatus = getPacketStatus();
  uint8_t snrPkt = (packetStatus >> 8) & 0xFF;
  if(snrPkt < 128) {
    return(snrPkt/4.0);
  } else {
    return((snrPkt - 256)/4.0);
  }
}

float SX126x::getFrequencyError() {
  // check active modem
  uint8_t modem = getPacketType();
  if(modem != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(0.0);
  }

  // read the raw frequency error register values
  uint8_t efeRaw[3] = {0};
  int16_t state = readRegister(RADIOLIB_SX126X_REG_FREQ_ERROR, &efeRaw[0], 1);
  RADIOLIB_ASSERT(state);
  state = readRegister(RADIOLIB_SX126X_REG_FREQ_ERROR + 1, &efeRaw[1], 1);
  RADIOLIB_ASSERT(state);
  state = readRegister(RADIOLIB_SX126X_REG_FREQ_ERROR + 2, &efeRaw[2], 1);
  RADIOLIB_ASSERT(state);
  uint32_t efe = ((uint32_t) efeRaw[0] << 16) | ((uint32_t) efeRaw[1] << 8) | efeRaw[2];
  efe &= 0x0FFFFF;

  float error = 0;

  // check the first bit
  if (efe & 0x80000) {
    // frequency error is negative
    efe |= (uint32_t) 0xFFF00000;
    efe = ~efe + 1;
    error = 1.55f * (float) efe / (1600.0f / (float) this->bandwidthKhz) * -1.0f;
  } else {
    error = 1.55f * (float) efe / (1600.0f / (float) this->bandwidthKhz);
  }

  return(error);
}

size_t SX126x::getPacketLength(bool update) {
  return(this->getPacketLength(update, NULL));
}

size_t SX126x::getPacketLength(bool update, uint8_t* offset) {
  (void)update;

  // in implicit mode, return the cached value
  if((getPacketType() == RADIOLIB_SX126X_PACKET_TYPE_LORA) && (this->headerType == RADIOLIB_SX126X_LORA_HEADER_IMPLICIT)) {
    return(this->implicitLen);
  }

  uint8_t rxBufStatus[2] = {0, 0};
  this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_RX_BUFFER_STATUS, rxBufStatus, 2);

  if(offset) { *offset = rxBufStatus[1]; }

  return((size_t)rxBufStatus[0]);
}

int16_t SX126x::fixedPacketLengthMode(uint8_t len) {
  return(setPacketMode(RADIOLIB_SX126X_GFSK_PACKET_FIXED, len));
}

int16_t SX126x::variablePacketLengthMode(uint8_t maxLen) {
  return(setPacketMode(RADIOLIB_SX126X_GFSK_PACKET_VARIABLE, maxLen));
}

RadioLibTime_t SX126x::getTimeOnAir(size_t len) {
  // everything is in microseconds to allow integer arithmetic
  // some constants have .25, these are multiplied by 4, and have _x4 postfix to indicate that fact
  uint8_t modem = getPacketType();
  if(modem == RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    uint32_t symbolLength_us = ((uint32_t)(1000 * 10) << this->spreadingFactor) / (this->bandwidthKhz * 10) ;
    uint8_t sfCoeff1_x4 = 17; // (4.25 * 4)
    uint8_t sfCoeff2 = 8;
    if(this->spreadingFactor == 5 || this->spreadingFactor == 6) {
      sfCoeff1_x4 = 25; // 6.25 * 4
      sfCoeff2 = 0;
    }
    uint8_t sfDivisor = 4*this->spreadingFactor;
    if(symbolLength_us >= 16000) {
      sfDivisor = 4*(this->spreadingFactor - 2);
    }
    const int8_t bitsPerCrc = 16;
    const int8_t N_symbol_header = this->headerType == RADIOLIB_SX126X_LORA_HEADER_EXPLICIT ? 20 : 0;

    // numerator of equation in section 6.1.4 of SX1268 datasheet v1.1 (might not actually be bitcount, but it has len * 8)
    int16_t bitCount = (int16_t) 8 * len + this->crcTypeLoRa * bitsPerCrc - 4 * this->spreadingFactor  + sfCoeff2 + N_symbol_header;
    if(bitCount < 0) {
      bitCount = 0;
    }
    // add (sfDivisor) - 1 to the numerator to give integer CEIL(...)
    uint16_t nPreCodedSymbols = (bitCount + (sfDivisor - 1)) / (sfDivisor);

    // preamble can be 65k, therefore nSymbol_x4 needs to be 32 bit
    uint32_t nSymbol_x4 = (this->preambleLengthLoRa + 8) * 4 + sfCoeff1_x4 + nPreCodedSymbols * (this->codingRate + 4) * 4;

    return((symbolLength_us * nSymbol_x4) / 4);
 
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(((uint32_t)len * 8 * this->bitRate) / (RADIOLIB_SX126X_CRYSTAL_FREQ * 32));
  
  } else if(modem == RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS) {
    // calculate the number of bits based on coding rate
    uint16_t N_bits;
    switch(this->lrFhssCr) {
      case RADIOLIB_SX126X_LR_FHSS_CR_5_6:
        N_bits = ((len * 6) + 4) / 5; // this is from the official LR11xx driver, but why the extra +4?
        break;
      case RADIOLIB_SX126X_LR_FHSS_CR_2_3:
        N_bits = (len * 3) / 2;
        break;
      case RADIOLIB_SX126X_LR_FHSS_CR_1_2:
        N_bits = len * 2;
        break;
      case RADIOLIB_SX126X_LR_FHSS_CR_1_3:
        N_bits = len * 3;
        break;
      default:
        return(RADIOLIB_ERR_INVALID_CODING_RATE);
    }

    // calculate number of bits when accounting for unaligned last block
    uint16_t N_payBits = (N_bits / RADIOLIB_SX126X_LR_FHSS_FRAG_BITS) * RADIOLIB_SX126X_LR_FHSS_BLOCK_BITS;
    uint16_t N_lastBlockBits = N_bits % RADIOLIB_SX126X_LR_FHSS_FRAG_BITS;
    if(N_lastBlockBits) {
      N_payBits += N_lastBlockBits + 2;
    }

    // add header bits
    uint16_t N_totalBits = (RADIOLIB_SX126X_LR_FHSS_HEADER_BITS * this->lrFhssHdrCount) + N_payBits;
    return(((uint32_t)N_totalBits * 8 * 1000000UL) / 488.28215f);
  
  }

  return(RADIOLIB_ERR_UNKNOWN);
}

RadioLibTime_t SX126x::calculateRxTimeout(RadioLibTime_t timeoutUs) {
  // the timeout value is given in units of 15.625 microseconds
  // the calling function should provide some extra width, as this number of units is truncated to integer
  RadioLibTime_t timeout = timeoutUs / 15.625f;
  return(timeout);
}

uint32_t SX126x::getIrqFlags() {
  uint8_t data[] = { 0x00, 0x00 };
  this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_IRQ_STATUS, data, 2);
  return(((uint32_t)(data[0]) << 8) | data[1]);
}

int16_t SX126x::setIrqFlags(uint32_t irq) {
  return(this->setDioIrqParams(irq, irq));
}

int16_t SX126x::clearIrqFlags(uint32_t irq) {
  return(this->clearIrqStatus(irq));
}

int16_t SX126x::implicitHeader(size_t len) {
  return(setHeaderType(RADIOLIB_SX126X_LORA_HEADER_IMPLICIT, len));
}

int16_t SX126x::explicitHeader() {
  return(setHeaderType(RADIOLIB_SX126X_LORA_HEADER_EXPLICIT));
}

int16_t SX126x::setRegulatorLDO() {
  return(setRegulatorMode(RADIOLIB_SX126X_REGULATOR_LDO));
}

int16_t SX126x::setRegulatorDCDC() {
  return(setRegulatorMode(RADIOLIB_SX126X_REGULATOR_DC_DC));
}

int16_t SX126x::setEncoding(uint8_t encoding) {
  return(setWhitening(encoding));
}

void SX126x::setRfSwitchPins(uint32_t rxEn, uint32_t txEn) {
  this->mod->setRfSwitchPins(rxEn, txEn);
}

void SX126x::setRfSwitchTable(const uint32_t (&pins)[Module::RFSWITCH_MAX_PINS], const Module::RfSwitchMode_t table[]) {
  this->mod->setRfSwitchTable(pins, table);
}

int16_t SX126x::forceLDRO(bool enable) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // update modulation parameters
  this->ldroAuto = false;
  this->ldrOptimize = (uint8_t)enable;
  return(setModulationParams(this->spreadingFactor, this->bandwidth, this->codingRate, this->ldrOptimize));
}

int16_t SX126x::autoLDRO() {
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  this->ldroAuto = true;
  return(RADIOLIB_ERR_NONE);
}

uint8_t SX126x::randomByte() {
  // set some magic registers
  this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_ANA_LNA, RADIOLIB_SX126X_LNA_RNG_ENABLED, 0, 0);
  this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_ANA_MIXER, RADIOLIB_SX126X_MIXER_RNG_ENABLED, 0, 0);

  // set mode to Rx
  setRx(RADIOLIB_SX126X_RX_TIMEOUT_INF);

  // wait a bit for the RSSI reading to stabilise
  this->mod->hal->delay(10);

  // read RSSI value 8 times, always keep just the least significant bit
  uint8_t randByte = 0x00;
  for(uint8_t i = 0; i < 8; i++) {
    uint8_t val = 0x00;
    readRegister(RADIOLIB_SX126X_REG_RANDOM_NUMBER_0, &val, sizeof(uint8_t));
    randByte |= ((val & 0x01) << i);
  }

  // set mode to standby
  standby();

  // restore the magic registers
  this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_ANA_LNA, RADIOLIB_SX126X_LNA_RNG_DISABLED, 0, 0);
  this->mod->SPIsetRegValue(RADIOLIB_SX126X_REG_ANA_MIXER, RADIOLIB_SX126X_MIXER_RNG_DISABLED, 0, 0);

  return(randByte);
}

int16_t SX126x::invertIQ(bool enable) {
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  if(enable) {
    this->invertIQEnabled = RADIOLIB_SX126X_LORA_IQ_INVERTED;
  } else {
    this->invertIQEnabled = RADIOLIB_SX126X_LORA_IQ_STANDARD;
  }

  return(setPacketParams(this->preambleLengthLoRa, this->crcTypeLoRa, this->implicitLen, this->headerType, this->invertIQEnabled));
}

int16_t SX126x::getModem(ModemType_t* modem) {
  RADIOLIB_ASSERT_PTR(modem);

  uint8_t packetType = getPacketType();
  switch(packetType) {
    case(RADIOLIB_SX126X_PACKET_TYPE_LORA):
      *modem = ModemType_t::RADIOLIB_MODEM_LORA;
      return(RADIOLIB_ERR_NONE);
    case(RADIOLIB_SX126X_PACKET_TYPE_GFSK):
      *modem = ModemType_t::RADIOLIB_MODEM_FSK;
      return(RADIOLIB_ERR_NONE);
    case(RADIOLIB_SX126X_PACKET_TYPE_LR_FHSS):
      *modem = ModemType_t::RADIOLIB_MODEM_LRFHSS;
      return(RADIOLIB_ERR_NONE);
  }
  
  return(RADIOLIB_ERR_WRONG_MODEM);
}

#if !RADIOLIB_EXCLUDE_DIRECT_RECEIVE
void SX126x::setDirectAction(void (*func)(void)) {
  setDio1Action(func);
}

void SX126x::readBit(uint32_t pin) {
  updateDirectBuffer((uint8_t)this->mod->hal->digitalRead(pin));
}
#endif

int16_t SX126x::uploadPatch(const uint32_t* patch, size_t len, bool nonvolatile) {
  // set to standby RC mode
  int16_t state = standby(RADIOLIB_SX126X_STANDBY_RC);
  RADIOLIB_ASSERT(state);

  // check the version
  #if RADIOLIB_DEBUG_BASIC
  char ver_pre[16];
  this->mod->SPIreadRegisterBurst(RADIOLIB_SX126X_REG_VERSION_STRING, 16, reinterpret_cast<uint8_t*>(ver_pre));
  RADIOLIB_DEBUG_BASIC_PRINTLN("Pre-update version string: %s", ver_pre);
  #endif

  // enable patch update
  this->mod->SPIwriteRegister(RADIOLIB_SX126X_REG_PATCH_UPDATE_ENABLE, RADIOLIB_SX126X_PATCH_UPDATE_ENABLED);
  
  // upload the patch
  uint8_t data[4];
  for(uint32_t i = 0; i < len / sizeof(uint32_t); i++) {
    uint32_t bin = 0;
    if(nonvolatile) {
      bin = RADIOLIB_NONVOLATILE_READ_DWORD(patch + i);
    } else {
      bin = patch[i];
    }
    data[0] = (bin >> 24) & 0xFF;
    data[1] = (bin >> 16) & 0xFF;
    data[2] = (bin >> 8) & 0xFF;
    data[3] = bin & 0xFF;
    this->mod->SPIwriteRegisterBurst(RADIOLIB_SX126X_REG_PATCH_MEMORY_BASE + i*sizeof(uint32_t), data, sizeof(uint32_t));
  }

  // disable patch update
  this->mod->SPIwriteRegister(RADIOLIB_SX126X_REG_PATCH_UPDATE_ENABLE, RADIOLIB_SX126X_PATCH_UPDATE_DISABLED);

  // update
  this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_PRAM_UPDATE, NULL, 0);

  // check the version again
  #if RADIOLIB_DEBUG_BASIC
  char ver_post[16];
  this->mod->SPIreadRegisterBurst(RADIOLIB_SX126X_REG_VERSION_STRING, 16, reinterpret_cast<uint8_t*>(ver_post));
  RADIOLIB_DEBUG_BASIC_PRINTLN("Post-update version string: %s", ver_post);
  #endif

  return(state);
}

int16_t SX126x::spectralScanStart(uint16_t numSamples, uint8_t window, uint8_t interval) {
  // abort first - not sure if this is strictly needed, but the example code does this
  spectralScanAbort();

  // set the RSSI window size
  this->mod->SPIwriteRegister(RADIOLIB_SX126X_REG_RSSI_AVG_WINDOW, window);

  // start Rx with infinite timeout
  int16_t state = setRx(RADIOLIB_SX126X_RX_TIMEOUT_INF);
  RADIOLIB_ASSERT(state);

  // now set the actual spectral scan parameters
  uint8_t data[3] = { (uint8_t)((numSamples >> 8) & 0xFF), (uint8_t)(numSamples & 0xFF), interval };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_SPECTR_SCAN_PARAMS, data, 3));
}

void SX126x::spectralScanAbort() {
  this->mod->SPIwriteRegister(RADIOLIB_SX126X_REG_RSSI_AVG_WINDOW, 0x00);
}

int16_t SX126x::spectralScanGetStatus() {
  uint8_t status = this->mod->SPIreadRegister(RADIOLIB_SX126X_REG_SPECTRAL_SCAN_STATUS);
  if(status == RADIOLIB_SX126X_SPECTRAL_SCAN_COMPLETED) {
    return(RADIOLIB_ERR_NONE);
  }
  return(RADIOLIB_ERR_RANGING_TIMEOUT);
}

int16_t SX126x::spectralScanGetResult(uint16_t* results) {
  // read the raw results
  uint8_t data[2*RADIOLIB_SX126X_SPECTRAL_SCAN_RES_SIZE];
  this->mod->SPIreadRegisterBurst(RADIOLIB_SX126X_REG_SPECTRAL_SCAN_RESULT, 2*RADIOLIB_SX126X_SPECTRAL_SCAN_RES_SIZE, data);

  // convert it
  for(uint8_t i = 0; i < RADIOLIB_SX126X_SPECTRAL_SCAN_RES_SIZE; i++) {
    results[i] = ((uint16_t)data[i*2] << 8) | ((uint16_t)data[i*2 + 1]);
  }
  return(RADIOLIB_ERR_NONE);
}

int16_t SX126x::setTCXO(float voltage, uint32_t delay) {
  // check if TCXO is enabled at all
  if(this->XTAL) {
    return(RADIOLIB_ERR_INVALID_TCXO_VOLTAGE);
  }

  // set mode to standby
  standby();

  // check RADIOLIB_SX126X_XOSC_START_ERR flag and clear it
  if(getDeviceErrors() & RADIOLIB_SX126X_XOSC_START_ERR) {
    clearDeviceErrors();
  }

  // check 0 V disable
  if(fabsf(voltage - 0.0f) <= 0.001f) {
    return(reset(true));
  }

  // check alowed voltage values
  uint8_t data[4];
  if(fabsf(voltage - 1.6f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_1_6;
  } else if(fabsf(voltage - 1.7f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_1_7;
  } else if(fabsf(voltage - 1.8f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_1_8;
  } else if(fabsf(voltage - 2.2f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_2_2;
  } else if(fabsf(voltage - 2.4f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_2_4;
  } else if(fabsf(voltage - 2.7f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_2_7;
  } else if(fabsf(voltage - 3.0f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_3_0;
  } else if(fabsf(voltage - 3.3f) <= 0.001f) {
    data[0] = RADIOLIB_SX126X_DIO3_OUTPUT_3_3;
  } else {
    return(RADIOLIB_ERR_INVALID_TCXO_VOLTAGE);
  }

  // calculate delay
  uint32_t delayValue = (float)delay / 15.625f;
  data[1] = (uint8_t)((delayValue >> 16) & 0xFF);
  data[2] = (uint8_t)((delayValue >> 8) & 0xFF);
  data[3] = (uint8_t)(delayValue & 0xFF);

  this->tcxoDelay = delay;

  // enable TCXO control on DIO3
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_DIO3_AS_TCXO_CTRL, data, 4));
}

int16_t SX126x::setDio2AsRfSwitch(bool enable) {
  uint8_t data = 0;
  if(enable) {
    data = RADIOLIB_SX126X_DIO2_AS_RF_SWITCH;
  } else {
    data = RADIOLIB_SX126X_DIO2_AS_IRQ;
  }
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_DIO2_AS_RF_SWITCH_CTRL, &data, 1));
}

int16_t SX126x::setFs() {
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_FS, NULL, 0));
}

int16_t SX126x::setTx(uint32_t timeout) {
  uint8_t data[] = { (uint8_t)((timeout >> 16) & 0xFF), (uint8_t)((timeout >> 8) & 0xFF), (uint8_t)(timeout & 0xFF)} ;
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_TX, data, 3));
}

int16_t SX126x::setRx(uint32_t timeout) {
  uint8_t data[] = { (uint8_t)((timeout >> 16) & 0xFF), (uint8_t)((timeout >> 8) & 0xFF), (uint8_t)(timeout & 0xFF) };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_RX, data, 3, true, false));
}

int16_t SX126x::setCad(uint8_t symbolNum, uint8_t detPeak, uint8_t detMin, uint8_t exitMode, RadioLibTime_t timeout) {
  // default CAD parameters are shown in Semtech AN1200.48, page 41.
  const uint8_t detPeakValues[6] = { 22, 22, 24, 25, 26, 30};

  // CAD parameters aren't available for SF-6. Just to be safe.
  if(this->spreadingFactor < 7) {
    this->spreadingFactor = 7;
  } else if(this->spreadingFactor > 12) {
    this->spreadingFactor = 12;
  }

  // build the packet with default configuration
  uint8_t data[7];
  data[0] = RADIOLIB_SX126X_CAD_ON_2_SYMB;
  data[1] = detPeakValues[this->spreadingFactor - 7];
  data[2] = RADIOLIB_SX126X_CAD_PARAM_DET_MIN;
  data[3] = RADIOLIB_SX126X_CAD_GOTO_STDBY;
  uint32_t timeout_raw = (float)timeout / 15.625f;
  data[4] = (uint8_t)((timeout_raw >> 16) & 0xFF);
  data[5] = (uint8_t)((timeout_raw >> 8) & 0xFF);
  data[6] = (uint8_t)(timeout_raw & 0xFF);

  // set user-provided values
  if(symbolNum != RADIOLIB_SX126X_CAD_PARAM_DEFAULT) {
    data[0] = symbolNum;
  }

  if(detPeak != RADIOLIB_SX126X_CAD_PARAM_DEFAULT) {
    data[1] = detPeak;
  }

  if(detMin != RADIOLIB_SX126X_CAD_PARAM_DEFAULT) {
    data[2] = detMin;
  }

  if(exitMode != RADIOLIB_SX126X_CAD_PARAM_DEFAULT) {
    data[3] = exitMode;
  }

  // configure parameters
  int16_t state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_CAD_PARAMS, data, 7);
  RADIOLIB_ASSERT(state);

  // start CAD
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_CAD, NULL, 0));
}

int16_t SX126x::setPaConfig(uint8_t paDutyCycle, uint8_t deviceSel, uint8_t hpMax, uint8_t paLut) {
  uint8_t data[] = { paDutyCycle, hpMax, deviceSel, paLut };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_PA_CONFIG, data, 4));
}

int16_t SX126x::writeRegister(uint16_t addr, uint8_t* data, uint8_t numBytes) {
  this->mod->SPIwriteRegisterBurst(addr, data, numBytes);
  return(RADIOLIB_ERR_NONE);
}

int16_t SX126x::readRegister(uint16_t addr, uint8_t* data, uint8_t numBytes) {
  // send the command
  this->mod->SPIreadRegisterBurst(addr, numBytes, data);

  // check the status
  int16_t state = this->mod->SPIcheckStream();
  return(state);
}

int16_t SX126x::writeBuffer(uint8_t* data, uint8_t numBytes, uint8_t offset) {
  uint8_t cmd[] = { RADIOLIB_SX126X_CMD_WRITE_BUFFER, offset };
  return(this->mod->SPIwriteStream(cmd, 2, data, numBytes));
}

int16_t SX126x::readBuffer(uint8_t* data, uint8_t numBytes, uint8_t offset) {
  uint8_t cmd[] = { RADIOLIB_SX126X_CMD_READ_BUFFER, offset };
  return(this->mod->SPIreadStream(cmd, 2, data, numBytes));
}

int16_t SX126x::setDioIrqParams(uint16_t irqMask, uint16_t dio1Mask, uint16_t dio2Mask, uint16_t dio3Mask) {
  uint8_t data[8] = {(uint8_t)((irqMask >> 8) & 0xFF), (uint8_t)(irqMask & 0xFF),
                     (uint8_t)((dio1Mask >> 8) & 0xFF), (uint8_t)(dio1Mask & 0xFF),
                     (uint8_t)((dio2Mask >> 8) & 0xFF), (uint8_t)(dio2Mask & 0xFF),
                     (uint8_t)((dio3Mask >> 8) & 0xFF), (uint8_t)(dio3Mask & 0xFF)};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_DIO_IRQ_PARAMS, data, 8));
}

int16_t SX126x::clearIrqStatus(uint16_t clearIrqParams) {
  uint8_t data[] = { (uint8_t)((clearIrqParams >> 8) & 0xFF), (uint8_t)(clearIrqParams & 0xFF) };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_CLEAR_IRQ_STATUS, data, 2));
}

int16_t SX126x::setRfFrequency(uint32_t frf) {
  uint8_t data[] = { (uint8_t)((frf >> 24) & 0xFF), (uint8_t)((frf >> 16) & 0xFF), (uint8_t)((frf >> 8) & 0xFF), (uint8_t)(frf & 0xFF) };
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_RF_FREQUENCY, data, 4));
}

int16_t SX126x::calibrateImage(float freq) {
  uint8_t data[2] = { 0, 0 };

  // try to match the frequency ranges
  int freqBand = (int)freq;
  if((freqBand >= 902) && (freqBand <= 928)) {
    data[0] = RADIOLIB_SX126X_CAL_IMG_902_MHZ_1;
    data[1] = RADIOLIB_SX126X_CAL_IMG_902_MHZ_2;
  } else if((freqBand >= 863) && (freqBand <= 870)) {
    data[0] = RADIOLIB_SX126X_CAL_IMG_863_MHZ_1;
    data[1] = RADIOLIB_SX126X_CAL_IMG_863_MHZ_2;
  } else if((freqBand >= 779) && (freqBand <= 787)) {
    data[0] = RADIOLIB_SX126X_CAL_IMG_779_MHZ_1;
    data[1] = RADIOLIB_SX126X_CAL_IMG_779_MHZ_2;
  } else if((freqBand >= 470) && (freqBand <= 510)) {
    data[0] = RADIOLIB_SX126X_CAL_IMG_470_MHZ_1;
    data[1] = RADIOLIB_SX126X_CAL_IMG_470_MHZ_2;
  } else if((freqBand >= 430) && (freqBand <= 440)) {
    data[0] = RADIOLIB_SX126X_CAL_IMG_430_MHZ_1;
    data[1] = RADIOLIB_SX126X_CAL_IMG_430_MHZ_2;
  }

  int16_t state;
  if(data[0]) {
    // matched with predefined ranges, do the calibration
    state = SX126x::calibrateImage(data);
  
  } else {
    // if nothing matched, try custom calibration - the may or may not work
    RADIOLIB_DEBUG_BASIC_PRINTLN("Failed to match predefined frequency range, trying custom");
    state = SX126x::calibrateImageRejection(freq - 4.0f, freq + 4.0f);
  
  }
  
  return(state);
}

int16_t SX126x::calibrateImageRejection(float freqMin, float freqMax) {
  // calculate the calibration coefficients and calibrate image
  uint8_t data[] = { (uint8_t)floor((freqMin - 1.0f) / 4.0f), (uint8_t)ceil((freqMax + 1.0f) / 4.0f) };
  data[0] = (data[0] % 2) ? data[0] : data[0] - 1;
  data[1] = (data[1] % 2) ? data[1] : data[1] + 1;
  return(this->calibrateImage(data));
}

int16_t SX126x::setPaRampTime(uint8_t rampTime) {
  return(this->setTxParams(this->pwr, rampTime));
}

int16_t SX126x::calibrateImage(uint8_t* data) {
  int16_t state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_CALIBRATE_IMAGE, data, 2);

  // if something failed, show the device errors
  #if RADIOLIB_DEBUG_BASIC
  if(state != RADIOLIB_ERR_NONE) {
    // unless mode is forced to standby, device errors will be 0
    standby();
    uint16_t errors = getDeviceErrors();
    RADIOLIB_DEBUG_BASIC_PRINTLN("Calibration failed, device errors: 0x%X", errors);
  }
  #endif
  return(state);
}

uint8_t SX126x::getPacketType() {
  uint8_t data = 0xFF;
  this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_PACKET_TYPE, &data, 1);
  return(data);
}

int16_t SX126x::setTxParams(uint8_t pwr, uint8_t rampTime) {
  uint8_t data[] = { pwr, rampTime };
  int16_t state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_TX_PARAMS, data, 2);
  if(state == RADIOLIB_ERR_NONE) {
    this->pwr = pwr;
  }
  return(state);
}

int16_t SX126x::setPacketMode(uint8_t mode, uint8_t len) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_GFSK) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // set requested packet mode
  int16_t state = setPacketParamsFSK(this->preambleLengthFSK, this->preambleDetLength, this->crcTypeFSK, this->syncWordLength, RADIOLIB_SX126X_GFSK_ADDRESS_FILT_OFF, this->whitening, mode, len);
  RADIOLIB_ASSERT(state);

  // update cached value
  this->packetType = mode;
  return(state);
}

int16_t SX126x::setHeaderType(uint8_t hdrType, size_t len) {
  // check active modem
  if(getPacketType() != RADIOLIB_SX126X_PACKET_TYPE_LORA) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // set requested packet mode
  int16_t state = setPacketParams(this->preambleLengthLoRa, this->crcTypeLoRa, len, hdrType, this->invertIQEnabled);
  RADIOLIB_ASSERT(state);

  // update cached value
  this->headerType = hdrType;
  this->implicitLen = len;

  return(state);
}

int16_t SX126x::setModulationParams(uint8_t sf, uint8_t bw, uint8_t cr, uint8_t ldro) {
  // calculate symbol length and enable low data rate optimization, if auto-configuration is enabled
  if(this->ldroAuto) {
    float symbolLength = (float)(uint32_t(1) << this->spreadingFactor) / (float)this->bandwidthKhz;
    if(symbolLength >= 16.0f) {
      this->ldrOptimize = RADIOLIB_SX126X_LORA_LOW_DATA_RATE_OPTIMIZE_ON;
    } else {
      this->ldrOptimize = RADIOLIB_SX126X_LORA_LOW_DATA_RATE_OPTIMIZE_OFF;
    }
  } else {
    this->ldrOptimize = ldro;
  }
  // 500/9/8  - 0x09 0x04 0x03 0x00 - SF9, BW125, 4/8
  // 500/11/8 - 0x0B 0x04 0x03 0x00 - SF11 BW125, 4/7
  uint8_t data[4] = {sf, bw, cr, this->ldrOptimize};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_MODULATION_PARAMS, data, 4));
}

int16_t SX126x::setModulationParamsFSK(uint32_t br, uint8_t sh, uint8_t rxBw, uint32_t freqDev) {
  uint8_t data[8] = {(uint8_t)((br >> 16) & 0xFF), (uint8_t)((br >> 8) & 0xFF), (uint8_t)(br & 0xFF),
                     sh, rxBw,
                     (uint8_t)((freqDev >> 16) & 0xFF), (uint8_t)((freqDev >> 8) & 0xFF), (uint8_t)(freqDev & 0xFF)};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_MODULATION_PARAMS, data, 8));
}

int16_t SX126x::setPacketParams(uint16_t preambleLen, uint8_t crcType, uint8_t payloadLen, uint8_t hdrType, uint8_t invertIQ) {
  int16_t state = fixInvertedIQ(invertIQ);
  RADIOLIB_ASSERT(state);
  uint8_t data[6] = {(uint8_t)((preambleLen >> 8) & 0xFF), (uint8_t)(preambleLen & 0xFF), hdrType, payloadLen, crcType, invertIQ};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_PACKET_PARAMS, data, 6));
}

int16_t SX126x::setPacketParamsFSK(uint16_t preambleLen, uint8_t preambleDetectorLen, uint8_t crcType, uint8_t syncWordLen, uint8_t addrCmp, uint8_t whiten, uint8_t packType, uint8_t payloadLen) {
  uint8_t data[9] = {(uint8_t)((preambleLen >> 8) & 0xFF), (uint8_t)(preambleLen & 0xFF),
                     preambleDetectorLen, syncWordLen, addrCmp,
                     packType, payloadLen, crcType, whiten};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_PACKET_PARAMS, data, 9));
}

int16_t SX126x::setBufferBaseAddress(uint8_t txBaseAddress, uint8_t rxBaseAddress) {
  uint8_t data[2] = {txBaseAddress, rxBaseAddress};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_BUFFER_BASE_ADDRESS, data, 2));
}

int16_t SX126x::setRegulatorMode(uint8_t mode) {
  uint8_t data[1] = {mode};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_REGULATOR_MODE, data, 1));
}

uint8_t SX126x::getStatus() {
  uint8_t data = 0;
  this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_STATUS, &data, 0);
  return(data);
}

uint32_t SX126x::getPacketStatus() {
  uint8_t data[3] = {0, 0, 0};
  this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_PACKET_STATUS, data, 3);
  return((((uint32_t)data[0]) << 16) | (((uint32_t)data[1]) << 8) | (uint32_t)data[2]);
}

uint16_t SX126x::getDeviceErrors() {
  uint8_t data[2] = {0, 0};
  this->mod->SPIreadStream(RADIOLIB_SX126X_CMD_GET_DEVICE_ERRORS, data, 2);
  uint16_t opError = (((uint16_t)data[0] & 0xFF) << 8) | ((uint16_t)data[1]);
  return(opError);
}

int16_t SX126x::clearDeviceErrors() {
  uint8_t data[2] = {RADIOLIB_SX126X_CMD_NOP, RADIOLIB_SX126X_CMD_NOP};
  return(this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_CLEAR_DEVICE_ERRORS, data, 2));
}

int16_t SX126x::setFrequencyRaw(float freq) {
  // calculate raw value
  this->freqMHz = freq;
  uint32_t frf = (this->freqMHz * (uint32_t(1) << RADIOLIB_SX126X_DIV_EXPONENT)) / RADIOLIB_SX126X_CRYSTAL_FREQ;
  return(setRfFrequency(frf));
}

int16_t SX126x::fixSensitivity() {
  // fix receiver sensitivity for 500 kHz LoRa
  // see SX1262/SX1268 datasheet, chapter 15 Known Limitations, section 15.1 for details

  // read current sensitivity configuration
  uint8_t sensitivityConfig = 0;
  int16_t state = readRegister(RADIOLIB_SX126X_REG_SENSITIVITY_CONFIG, &sensitivityConfig, 1);
  RADIOLIB_ASSERT(state);

  // fix the value for LoRa with 500 kHz bandwidth
  if((getPacketType() == RADIOLIB_SX126X_PACKET_TYPE_LORA) && (fabsf(this->bandwidthKhz - 500.0f) <= 0.001f)) {
    sensitivityConfig &= 0xFB;
  } else {
    sensitivityConfig |= 0x04;
  }
  return(writeRegister(RADIOLIB_SX126X_REG_SENSITIVITY_CONFIG, &sensitivityConfig, 1));
}

int16_t SX126x::fixPaClamping(bool enable) {
  // fixes overly eager PA clamping
  // see SX1262/SX1268 datasheet, chapter 15 Known Limitations, section 15.2 for details

  // read current clamping configuration
  uint8_t clampConfig = 0;
  int16_t state = readRegister(RADIOLIB_SX126X_REG_TX_CLAMP_CONFIG, &clampConfig, 1);
  RADIOLIB_ASSERT(state);

  // apply or undo workaround
  if (enable)
    clampConfig |= 0x1E;
  else
    clampConfig = (clampConfig & ~0x1E) | 0x08;

  return(writeRegister(RADIOLIB_SX126X_REG_TX_CLAMP_CONFIG, &clampConfig, 1));
}

int16_t SX126x::fixImplicitTimeout() {
  // fixes timeout in implicit header mode
  // see SX1262/SX1268 datasheet, chapter 15 Known Limitations, section 15.3 for details

  //check if we're in implicit LoRa mode
  if(!((this->headerType == RADIOLIB_SX126X_LORA_HEADER_IMPLICIT) && (getPacketType() == RADIOLIB_SX126X_PACKET_TYPE_LORA))) {
    return(RADIOLIB_ERR_WRONG_MODEM);
  }

  // stop RTC counter
  uint8_t rtcStop = 0x00;
  int16_t state = writeRegister(RADIOLIB_SX126X_REG_RTC_CTRL, &rtcStop, 1);
  RADIOLIB_ASSERT(state);

  // read currently active event
  uint8_t rtcEvent = 0;
  state = readRegister(RADIOLIB_SX126X_REG_EVENT_MASK, &rtcEvent, 1);
  RADIOLIB_ASSERT(state);

  // clear events
  rtcEvent |= 0x02;
  return(writeRegister(RADIOLIB_SX126X_REG_EVENT_MASK, &rtcEvent, 1));
}

int16_t SX126x::fixInvertedIQ(uint8_t iqConfig) {
  // fixes IQ configuration for inverted IQ
  // see SX1262/SX1268 datasheet, chapter 15 Known Limitations, section 15.4 for details

  // read current IQ configuration
  uint8_t iqConfigCurrent = 0;
  int16_t state = readRegister(RADIOLIB_SX126X_REG_IQ_CONFIG, &iqConfigCurrent, 1);
  RADIOLIB_ASSERT(state);

  // set correct IQ configuration
  if(iqConfig == RADIOLIB_SX126X_LORA_IQ_INVERTED) {
    iqConfigCurrent &= 0xFB;
  } else {
    iqConfigCurrent |= 0x04;
  }

  // update with the new value
  return(writeRegister(RADIOLIB_SX126X_REG_IQ_CONFIG, &iqConfigCurrent, 1));
}

Module* SX126x::getMod() {
  return(this->mod);
}

int16_t SX126x::modSetup(float tcxoVoltage, bool useRegulatorLDO, uint8_t modem) {
  // set module properties
  this->mod->init();
  this->mod->hal->pinMode(this->mod->getIrq(), this->mod->hal->GpioModeInput);
  this->mod->hal->pinMode(this->mod->getGpio(), this->mod->hal->GpioModeInput);
  this->mod->spiConfig.widths[RADIOLIB_MODULE_SPI_WIDTH_ADDR] = Module::BITS_16;
  this->mod->spiConfig.widths[RADIOLIB_MODULE_SPI_WIDTH_CMD] = Module::BITS_8;
  this->mod->spiConfig.statusPos = 1;
  this->mod->spiConfig.cmds[RADIOLIB_MODULE_SPI_COMMAND_READ] = RADIOLIB_SX126X_CMD_READ_REGISTER;
  this->mod->spiConfig.cmds[RADIOLIB_MODULE_SPI_COMMAND_WRITE] = RADIOLIB_SX126X_CMD_WRITE_REGISTER;
  this->mod->spiConfig.cmds[RADIOLIB_MODULE_SPI_COMMAND_NOP] = RADIOLIB_SX126X_CMD_NOP;
  this->mod->spiConfig.cmds[RADIOLIB_MODULE_SPI_COMMAND_STATUS] = RADIOLIB_SX126X_CMD_GET_STATUS;
  this->mod->spiConfig.stream = true;
  this->mod->spiConfig.parseStatusCb = SPIparseStatus;
  
  // try to find the SX126x chip
  if(!SX126x::findChip(this->chipType)) {
    RADIOLIB_DEBUG_BASIC_PRINTLN("No SX126x found!");
    this->mod->term();
    return(RADIOLIB_ERR_CHIP_NOT_FOUND);
  }
  RADIOLIB_DEBUG_BASIC_PRINTLN("M\tSX126x");

  // reset the module and verify startup
  int16_t state = reset();
  RADIOLIB_ASSERT(state);

  // set mode to standby
  state = standby();
  RADIOLIB_ASSERT(state);

  // set TCXO control, if requested
  if(!this->XTAL && tcxoVoltage > 0.0f) {
    state = setTCXO(tcxoVoltage);
    RADIOLIB_ASSERT(state);
  }

  // configure settings not accessible by API
  state = config(modem);
  RADIOLIB_ASSERT(state);

  if (useRegulatorLDO) {
    state = setRegulatorLDO();
  } else {
    state = setRegulatorDCDC();
  }
  return(state);
}

int16_t SX126x::config(uint8_t modem) {
  // reset buffer base address
  int16_t state = setBufferBaseAddress();
  RADIOLIB_ASSERT(state);

  // set modem
  uint8_t data[7];
  data[0] = modem;
  state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_PACKET_TYPE, data, 1);
  RADIOLIB_ASSERT(state);

  // set Rx/Tx fallback mode to STDBY_RC
  data[0] = this->standbyXOSC ? RADIOLIB_SX126X_RX_TX_FALLBACK_MODE_STDBY_XOSC : RADIOLIB_SX126X_RX_TX_FALLBACK_MODE_STDBY_RC;
  state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_RX_TX_FALLBACK_MODE, data, 1);
  RADIOLIB_ASSERT(state);

  // set some CAD parameters - will be overwritten when calling CAD anyway
  data[0] = RADIOLIB_SX126X_CAD_ON_8_SYMB;
  data[1] = this->spreadingFactor + 13;
  data[2] = RADIOLIB_SX126X_CAD_PARAM_DET_MIN;
  data[3] = RADIOLIB_SX126X_CAD_GOTO_STDBY;
  data[4] = 0x00;
  data[5] = 0x00;
  data[6] = 0x00;
  state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_SET_CAD_PARAMS, data, 7);
  RADIOLIB_ASSERT(state);

  // clear IRQ
  state = clearIrqStatus();
  state |= setDioIrqParams(RADIOLIB_SX126X_IRQ_NONE, RADIOLIB_SX126X_IRQ_NONE);
  RADIOLIB_ASSERT(state);

  // calibrate all blocks
  data[0] = RADIOLIB_SX126X_CALIBRATE_ALL;
  state = this->mod->SPIwriteStream(RADIOLIB_SX126X_CMD_CALIBRATE, data, 1, true, false);
  RADIOLIB_ASSERT(state);

  // wait for calibration completion
  this->mod->hal->delay(5);
  while(this->mod->hal->digitalRead(this->mod->getGpio())) {
    this->mod->hal->yield();
  }

  // check calibration result
  state = this->mod->SPIcheckStream();

  // if something failed, show the device errors
  #if RADIOLIB_DEBUG_BASIC
  if(state != RADIOLIB_ERR_NONE) {
    // unless mode is forced to standby, device errors will be 0
    standby();
    uint16_t errors = getDeviceErrors();
    RADIOLIB_DEBUG_BASIC_PRINTLN("Calibration failed, device errors: 0x%X", errors);
  }
  #endif

  return(state);
}

int16_t SX126x::SPIparseStatus(uint8_t in) {
  if((in & 0b00001110) == RADIOLIB_SX126X_STATUS_CMD_TIMEOUT) {
    return(RADIOLIB_ERR_SPI_CMD_TIMEOUT);
  } else if((in & 0b00001110) == RADIOLIB_SX126X_STATUS_CMD_INVALID) {
    return(RADIOLIB_ERR_SPI_CMD_INVALID);
  } else if((in & 0b00001110) == RADIOLIB_SX126X_STATUS_CMD_FAILED) {
    return(RADIOLIB_ERR_SPI_CMD_FAILED);
  } else if((in == 0x00) || (in == 0xFF)) {
    return(RADIOLIB_ERR_CHIP_NOT_FOUND);
  }
  return(RADIOLIB_ERR_NONE);
}

bool SX126x::findChip(const char* verStr) {
  uint8_t i = 0;
  bool flagFound = false;
  while((i < 10) && !flagFound) {
    // reset the module
    reset();

    // read the version string
    char version[16];
    this->mod->SPIreadRegisterBurst(RADIOLIB_SX126X_REG_VERSION_STRING, 16, reinterpret_cast<uint8_t*>(version));

    // check version register
    if(strncmp(verStr, version, 6) == 0) {
      RADIOLIB_DEBUG_BASIC_PRINTLN("Found SX126x: RADIOLIB_SX126X_REG_VERSION_STRING:");
      RADIOLIB_DEBUG_BASIC_HEXDUMP(reinterpret_cast<uint8_t*>(version), 16, RADIOLIB_SX126X_REG_VERSION_STRING);
      RADIOLIB_DEBUG_BASIC_PRINTLN();
      flagFound = true;
    } else {
      #if RADIOLIB_DEBUG_BASIC
        RADIOLIB_DEBUG_BASIC_PRINTLN("SX126x not found! (%d of 10 tries) RADIOLIB_SX126X_REG_VERSION_STRING:", i + 1);
        RADIOLIB_DEBUG_BASIC_HEXDUMP(reinterpret_cast<uint8_t*>(version), 16, RADIOLIB_SX126X_REG_VERSION_STRING);
        RADIOLIB_DEBUG_BASIC_PRINTLN("Expected string: %s", verStr);
      #endif
      this->mod->hal->delay(10);
      i++;
    }
  }

  return(flagFound);
}

#endif