124 lines
3.5 KiB
C++
124 lines
3.5 KiB
C++
/*
|
|
RadioLib STM32WLx Receive Example
|
|
|
|
This example listens for LoRa transmissions using STM32WL MCU with
|
|
integrated (SX126x) LoRa radio.
|
|
|
|
To successfully receive data, the following settings have to be the same
|
|
on both transmitter and receiver:
|
|
- carrier frequency
|
|
- bandwidth
|
|
- spreading factor
|
|
- coding rate
|
|
- sync word
|
|
- preamble length
|
|
|
|
This example assumes Nucleo WL55JC1 is used. For other Nucleo boards
|
|
or standalone STM32WL, some configuration such as TCXO voltage and
|
|
RF switch control may have to be adjusted.
|
|
|
|
For default module settings, see the wiki page
|
|
https://github.com/jgromes/RadioLib/wiki/Default-configuration#sx126x---lora-modem
|
|
|
|
For full API reference, see the GitHub Pages
|
|
https://jgromes.github.io/RadioLib/
|
|
*/
|
|
|
|
// include the library
|
|
#include <RadioLib.h>
|
|
|
|
// no need to configure pins, signals are routed to the radio internally
|
|
STM32WLx radio = new STM32WLx_Module();
|
|
|
|
// set RF switch configuration for Nucleo WL55JC1
|
|
// NOTE: other boards may be different!
|
|
static const uint8_t rfswitch_pins[] =
|
|
{PC3, PC4, PC5};
|
|
static const Module::RfSwitchMode_t rfswitch_table[] = {
|
|
{STM32WLx::MODE_IDLE, {LOW, LOW, LOW}},
|
|
{STM32WLx::MODE_RX, {HIGH, HIGH, LOW}},
|
|
{STM32WLx::MODE_TX_LP, {HIGH, HIGH, HIGH}},
|
|
{STM32WLx::MODE_TX_HP, {HIGH, LOW, HIGH}},
|
|
END_OF_MODE_TABLE,
|
|
};
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
|
|
// set RF switch control configuration
|
|
// this has to be done prior to calling begin()
|
|
radio.setRfSwitchTable(rfswitch_pins, rfswitch_table);
|
|
|
|
// initialize STM32WL with default settings, except frequency
|
|
Serial.print(F("[STM32WL] Initializing ... "));
|
|
int state = radio.begin(868.0);
|
|
if (state == RADIOLIB_ERR_NONE) {
|
|
Serial.println(F("success!"));
|
|
} else {
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
while (true);
|
|
}
|
|
|
|
// set appropriate TCXO voltage for Nucleo WL55JC1
|
|
state = radio.setTCXO(1.7);
|
|
if (state == RADIOLIB_ERR_NONE) {
|
|
Serial.println(F("success!"));
|
|
} else {
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
while (true);
|
|
}
|
|
}
|
|
|
|
void loop() {
|
|
Serial.print(F("[STM32WL] Waiting for incoming transmission ... "));
|
|
|
|
// you can receive data as an Arduino String
|
|
// NOTE: receive() is a blocking method!
|
|
// See example ReceiveInterrupt for details
|
|
// on non-blocking reception method.
|
|
String str;
|
|
int state = radio.receive(str);
|
|
|
|
// you can also receive data as byte array
|
|
/*
|
|
byte byteArr[8];
|
|
int state = radio.receive(byteArr, 8);
|
|
*/
|
|
|
|
if (state == RADIOLIB_ERR_NONE) {
|
|
// packet was successfully received
|
|
Serial.println(F("success!"));
|
|
|
|
// print the data of the packet
|
|
Serial.print(F("[STM32WL] Data:\t\t"));
|
|
Serial.println(str);
|
|
|
|
// print the RSSI (Received Signal Strength Indicator)
|
|
// of the last received packet
|
|
Serial.print(F("[STM32WL] RSSI:\t\t"));
|
|
Serial.print(radio.getRSSI());
|
|
Serial.println(F(" dBm"));
|
|
|
|
// print the SNR (Signal-to-Noise Ratio)
|
|
// of the last received packet
|
|
Serial.print(F("[STM32WL] SNR:\t\t"));
|
|
Serial.print(radio.getSNR());
|
|
Serial.println(F(" dB"));
|
|
|
|
} else if (state == RADIOLIB_ERR_RX_TIMEOUT) {
|
|
// timeout occurred while waiting for a packet
|
|
Serial.println(F("timeout!"));
|
|
|
|
} else if (state == RADIOLIB_ERR_CRC_MISMATCH) {
|
|
// packet was received, but is malformed
|
|
Serial.println(F("CRC error!"));
|
|
|
|
} else {
|
|
// some other error occurred
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
|
|
}
|
|
}
|