101 lines
2.8 KiB
C++
101 lines
2.8 KiB
C++
/*
|
|
RadioLib SX126x Transmit Example
|
|
|
|
This example transmits packets using SX1262 LoRa radio module.
|
|
Each packet contains up to 256 bytes of data, in the form of:
|
|
- Arduino String
|
|
- null-terminated char array (C-string)
|
|
- arbitrary binary data (byte array)
|
|
|
|
Other modules from SX126x family can also be used.
|
|
*/
|
|
|
|
// include the library
|
|
#include <RadioLib.h>
|
|
|
|
// SX1262 module is in slot A on the shield
|
|
SX1262 lora = RadioShield.ModuleA;
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
|
|
// initialize SX1262 with default settings
|
|
Serial.print(F("[SX1262] Initializing ... "));
|
|
// carrier frequency: 434.0 MHz
|
|
// bandwidth: 125.0 kHz
|
|
// spreading factor: 9
|
|
// coding rate: 7
|
|
// sync word: 0x1424 (private network)
|
|
// output power: 14 dBm
|
|
// current limit: 60 mA
|
|
// preamble length: 8 symbols
|
|
// CRC: enabled
|
|
int state = lora.begin();
|
|
if (state == ERR_NONE) {
|
|
Serial.println(F("success!"));
|
|
} else {
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
while (true);
|
|
}
|
|
|
|
// NOTE: Some SX126x modules use TCXO
|
|
// (Temprature-Compensated Crystal Oscillator).
|
|
// To be able to use these modules, TCXO
|
|
// control must be enabled by calling
|
|
// setTCXO() and specifying the reference
|
|
// voltage.
|
|
/*
|
|
Serial.print(F("[SX1262] Setting TCXO reference ... "));
|
|
// enable TCXO
|
|
// reference voltage: 1.6 V
|
|
// timeout: 5000 us
|
|
state = lora.setTCXO(1.6);
|
|
if (state == ERR_NONE) {
|
|
Serial.println(F("success!"));
|
|
} else {
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
while (true);
|
|
}
|
|
*/
|
|
}
|
|
|
|
void loop() {
|
|
Serial.print(F("[SX1262] Transmitting packet ... "));
|
|
|
|
// you can transmit C-string or Arduino string up to
|
|
// 256 characters long
|
|
// NOTE: transmit() is a blocking method!
|
|
// See example SX126x_Transmit_Interrupt for details
|
|
// on non-blocking transmission method.
|
|
int state = lora.transmit("Hello World!");
|
|
|
|
// you can also transmit byte array up to 256 bytes long
|
|
/*
|
|
byte byteArr[] = {0x01, 0x23, 0x45, 0x56, 0x78, 0xAB, 0xCD, 0xEF};
|
|
int state = lora.transmit(byteArr, 8);
|
|
*/
|
|
|
|
if (state == ERR_NONE) {
|
|
// the packet was successfully transmitted
|
|
Serial.println(F(" success!"));
|
|
|
|
// print measured data rate
|
|
Serial.print(F("[SX1262] Datarate:\t"));
|
|
Serial.print(lora.getDataRate());
|
|
Serial.println(F(" bps"));
|
|
|
|
} else if (state == ERR_PACKET_TOO_LONG) {
|
|
// the supplied packet was longer than 256 bytes
|
|
Serial.println(F(" too long!"));
|
|
|
|
} else if (state == ERR_TX_TIMEOUT) {
|
|
// timeout occured while transmitting packet
|
|
Serial.println(F(" timeout!"));
|
|
|
|
}
|
|
|
|
// wait for a second before transmitting again
|
|
delay(1000);
|
|
}
|