RadioLibSmol/examples/LR11x0/LR11x0_Receive_Interrupt/LR11x0_Receive_Interrupt.ino

/*
  RadioLib LR11x0 Receive with Interrupts Example

  This example listens for LoRa transmissions and tries to
  receive them. Once a packet is received, an interrupt is
  triggered. To successfully receive data, the following
  settings have to be the same on both transmitter
  and receiver:
    - carrier frequency
    - bandwidth
    - spreading factor
    - coding rate
    - sync word

  Other modules from LR11x0 family can also be used.
  
  This example assumes Seeed Studio Wio WM1110 is used.
  For other LR11x0 modules, some configuration such as
  RF switch control may have to be adjusted.

  For default module settings, see the wiki page
  https://github.com/jgromes/RadioLib/wiki/Default-configuration#lr11x0---lora-modem

  For full API reference, see the GitHub Pages
  https://jgromes.github.io/RadioLib/
*/

// include the library
#include <RadioLib.h>

// LR1110 has the following connections:
// NSS pin:   10
// IRQ pin:   2
// NRST pin:  3
// BUSY pin:  9
LR1110 radio = new Module(10, 2, 3, 9);

// set RF switch configuration for Wio WM1110
// Wio WM1110 uses DIO5 and DIO6 for RF switching
// NOTE: other boards may be different!
static const uint32_t rfswitch_dio_pins[] = { 
  RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6,
  RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
};

static const Module::RfSwitchMode_t rfswitch_table[] = {
  // mode                  DIO5  DIO6 
  { LR11x0::MODE_STBY,   { LOW,  LOW  } },
  { LR11x0::MODE_RX,     { HIGH, LOW  } },
  { LR11x0::MODE_TX,     { HIGH, HIGH } },
  { LR11x0::MODE_TX_HP,  { LOW,  HIGH } },
  { LR11x0::MODE_TX_HF,  { LOW,  LOW  } },
  { LR11x0::MODE_GNSS,   { LOW,  LOW  } },
  { LR11x0::MODE_WIFI,   { LOW,  LOW  } },
  END_OF_MODE_TABLE,
};

void setup() {
  Serial.begin(9600);

  // set RF switch control configuration
  // this has to be done prior to calling begin()
  radio.setRfSwitchTable(rfswitch_dio_pins, rfswitch_table);

  // initialize LR1110 with default settings
  Serial.print(F("[LR1110] Initializing ... "));
  int state = radio.begin();
  if (state == RADIOLIB_ERR_NONE) {
    Serial.println(F("success!"));
  } else {
    Serial.print(F("failed, code "));
    Serial.println(state);
    while (true);
  }

  // set the function that will be called
  // when new packet is received
  radio.setPacketReceivedAction(setFlag);

  // start listening for LoRa packets
  Serial.print(F("[LR1110] Starting to listen ... "));
  state = radio.startReceive();
  if (state == RADIOLIB_ERR_NONE) {
    Serial.println(F("success!"));
  } else {
    Serial.print(F("failed, code "));
    Serial.println(state);
    while (true);
  }

  // if needed, 'listen' mode can be disabled by calling
  // any of the following methods:
  //
  // radio.standby()
  // radio.sleep()
  // radio.transmit();
  // radio.receive();
  // radio.scanChannel();
}

// flag to indicate that a packet was received
volatile bool receivedFlag = false;

// this function is called when a complete packet
// is received by the module
// IMPORTANT: this function MUST be 'void' type
//            and MUST NOT have any arguments!
#if defined(ESP8266) || defined(ESP32)
  ICACHE_RAM_ATTR
#endif
void setFlag(void) {
  // we got a packet, set the flag
  receivedFlag = true;
}

void loop() {
  // check if the flag is set
  if(receivedFlag) {
    // reset flag
    receivedFlag = false;

    // you can read received data as an Arduino String
    String str;
    int state = radio.readData(str);

    // you can also read received data as byte array
    /*
      byte byteArr[8];
      int numBytes = radio.getPacketLength();
      int state = radio.readData(byteArr, numBytes);
    */

    if (state == RADIOLIB_ERR_NONE) {
      // packet was successfully received
      Serial.println(F("[LR1110] Received packet!"));

      // print data of the packet
      Serial.print(F("[LR1110] Data:\t\t"));
      Serial.println(str);

      // print RSSI (Received Signal Strength Indicator)
      Serial.print(F("[LR1110] RSSI:\t\t"));
      Serial.print(radio.getRSSI());
      Serial.println(F(" dBm"));

      // print SNR (Signal-to-Noise Ratio)
      Serial.print(F("[LR1110] SNR:\t\t"));
      Serial.print(radio.getSNR());
      Serial.println(F(" dB"));

    } else if (state == RADIOLIB_ERR_CRC_MISMATCH) {
      // packet was received, but is malformed
      Serial.println(F("CRC error!"));

    } else {
      // some other error occurred
      Serial.print(F("failed, code "));
      Serial.println(state);

    }
  }
}