/*
   RadioLib AX.25 Transmit AFSK Example

   This example sends AX.25 messages using
   SX1278's FSK modem. The data is modulated
   as AFSK at 1200 baud using Bell 202 tones.

   Other modules that can be used for AX.25
   with AFSK modulation:
    - SX127x/RFM9x
    - RF69
    - SX1231
    - CC1101
    - nRF24
    - Si443x/RFM2x
    - SX126x/LLCC68 (only devices without TCXO!)

   For default module settings, see the wiki page
   https://github.com/jgromes/RadioLib/wiki/Default-configuration

   For full API reference, see the GitHub Pages
   https://jgromes.github.io/RadioLib/
*/

// include the library
#include <RadioLib.h>

// SX1278 has the following connections:
// NSS pin:   10
// DIO0 pin:  2
// RESET pin: 9
// DIO1 pin:  3
SX1278 radio = new Module(10, 2, 9, 3);

// or using RadioShield
// https://github.com/jgromes/RadioShield
//SX1278 radio = RadioShield.ModuleA;

// create AFSK client instance using the FSK module
// this requires connection to the module direct
// input pin, here connected to Arduino pin 5
// SX127x/RFM9x:  DIO2
// RF69:          DIO2
// SX1231:        DIO2
// CC1101:        GDO2
// Si443x/RFM2x:  GPIO
// SX126x/LLCC68: DIO2
AFSKClient audio(&radio, 5);

// create AX.25 client instance using the AFSK instance
AX25Client ax25(&audio);

void setup() {
  Serial.begin(9600);

  // initialize SX1278 with default settings
  Serial.print(F("[SX1278] Initializing ... "));
  int state = radio.beginFSK();

  // when using one of the non-LoRa modules for AX.25
  // (RF69, CC1101,, Si4432 etc.), use the basic begin() method
  // int state = radio.begin();

  if(state == RADIOLIB_ERR_NONE) {
    Serial.println(F("success!"));
  } else {
    Serial.print(F("failed, code "));
    Serial.println(state);
    while(true);
  }

  // initialize AX.25 client
  Serial.print(F("[AX.25] Initializing ... "));
  // source station callsign:     "N7LEM"
  // source station SSID:         0
  // preamble length:             8 bytes
  state = ax25.begin("N7LEM");
  if(state == RADIOLIB_ERR_NONE) {
    Serial.println(F("success!"));
  } else {
    Serial.print(F("failed, code "));
    Serial.println(state);
    while(true);
  }

  // Sometimes, it may be required to adjust audio
  // frequencies to match the expected 1200/2200 Hz tones.
  // The following method will offset mark frequency by
  // 100 Hz up and space frequency by 100 Hz down
  /*
    Serial.print(F("[AX.25] Setting correction ... "));
    state = ax25.setCorrection(100, -100);
    if(state == RADIOLIB_ERR_NONE) {
      Serial.println(F("success!"));
    } else {
      Serial.print(F("failed, code "));
      Serial.println(state);
      while(true);
    }
  */
}

void loop() {
  // send AX.25 unnumbered information frame
  Serial.print(F("[AX.25] Sending UI frame ... "));
  // destination station callsign:     "NJ7P"
  // destination station SSID:         0
  int state = ax25.transmit("Hello World!", "NJ7P");
  if (state == RADIOLIB_ERR_NONE) {
    // the packet was successfully transmitted
    Serial.println(F("success!"));

  } else {
    // some error occurred
    Serial.print(F("failed, code "));
    Serial.println(state);

  }

  delay(1000);
}