#ifndef _KITELIB_TYPES_H
#define _KITELIB_TYPES_H

#if ARDUINO >= 100
  #include "Arduino.h"
#else
  #include "WProgram.h"
#endif

//#define DEBUG

/*#ifdef DEBUG
  #define DEBUG_BEGIN(x)                Serial.begin (x)
  #define DEBUG_PRINT(x)                Serial.print (x)
  #define DEBUG_PRINT_DEC(x)            Serial.print (x, DEC)
  #define DEBUG_PRINT_HEX(x)            Serial.print (x, HEX)
  #define DEBUG_PRINTLN(x)              Serial.println (x)
  #define DEBUG_PRINT_STR(x)            Serial.print (F(x))
  #define DEBUG_PRINTLN_STR(x)          Serial.println (F(x))
#else*/
  #define DEBUG_BEGIN(x)
  #define DEBUG_PRINT(x)
  #define DEBUG_PRINT_DEC(x)
  #define DEBUG_PRINT_HEX(x)
  #define DEBUG_PRINTLN(x)
  #define DEBUG_PRINT_STR(x)
  #define DEBUG_PRINTLN_STR(x)
//#endif

// Shield configuration
#define USE_SPI                           0x00
#define USE_UART                          0x01
#define USE_I2C                           0x02
#define INT_NONE                          0x00
#define INT_0                             0x01
#define INT_1                             0x02
#define INT_BOTH                          0x03

// UART configuration
#define UART_STOPBIT_1                    0x01
#define UART_STOPBIT_1_5                  0x02
#define UART_STOPBIT_2                    0x03
#define UART_PARITY_NONE                  0x00
#define UART_PARITY_ODD                   0x01
#define UART_PARITY_EVEN                  0x02
#define UART_FLOW_NONE                    0x00
#define UART_FLOW_RTS                     0x01
#define UART_FLOW_CTS                     0x02
#define UART_FLOW_BOTH                    0x03

// Common error codes
#define ERR_NONE                          0x00
#define ERR_UNKNOWN                       0x63  // maximum error code value is 99, so that it does not interfere with HTTP status codes

// SX1278/SX1272/RF69 error codes
#define ERR_CHIP_NOT_FOUND                0x01
#define ERR_EEPROM_NOT_INITIALIZED        0x02
#define ERR_PACKET_TOO_LONG               0x03
#define ERR_TX_TIMEOUT                    0x04
#define ERR_RX_TIMEOUT                    0x05
#define ERR_CRC_MISMATCH                  0x06
#define ERR_INVALID_BANDWIDTH             0x07
#define ERR_INVALID_SPREADING_FACTOR      0x08
#define ERR_INVALID_CODING_RATE           0x09
#define ERR_INVALID_BIT_RANGE             0x10

// ESP8266 error codes
#define ERR_AT_FAILED                     0x01
#define ERR_URL_MALFORMED                 0x02
#define ERR_RESPONSE_MALFORMED_AT         0x03
#define ERR_RESPONSE_MALFORMED            0x04
#define ERR_MQTT_CONN_VERSION_REJECTED    0x05
#define ERR_MQTT_CONN_ID_REJECTED         0x06
#define ERR_MQTT_CONN_SERVER_UNAVAILABLE  0x07
#define MQTT_CONN_BAD_USERNAME_PASSWORD   0x08
#define ERR_MQTT_CONN_NOT_AUTHORIZED      0x09

// XBee error codes
#define ERR_CMD_MODE_FAILED               0x02

enum Slot {SlotA, SlotB};

enum Bandwidth {BW_7_80_KHZ, BW_10_40_KHZ, BW_15_60_KHZ, BW_20_80_KHZ, BW_31_25_KHZ, BW_41_70_KHZ, BW_62_50_KHZ, BW_125_00_KHZ, BW_250_00_KHZ, BW_500_00_KHZ};
enum SpreadingFactor {SF_6, SF_7, SF_8, SF_9, SF_10, SF_11, SF_12};
enum CodingRate {CR_4_5, CR_4_6, CR_4_7, CR_4_8};

#endif