[nRF24] Removed unsupported example

examples/nRF24/nRF24_Transmit/nRF24_Transmit.ino

@@ -1,102 +0,0 @@
-/*
-   RadioLib nRF24 Transmit Example
-*/
-
-// include the library
-#include <RadioLib.h>
-
-// nRF24 is in slot A on the shield
-nRF24 nrf = RadioShield.ModuleA;
-
-void setup() {
-  Serial.begin(9600);
-
-  // initialize nRF24
-  Serial.print(F("[nRF24] Initializing ... "));
-  // carrier frequency:           2400 MHz
-  // data rate:                   1000 kbps
-  // address width:               5 bytes
-  int state = nrf.begin();
-  if(state == ERR_NONE) {
-    Serial.println(F("success!"));
-  } else {
-    Serial.print(F("failed, code "));
-    Serial.println(state);
-    while(true);
-  }
-
-  // set receive pipe 0 address
-  // NOTE: address width in bytes MUST be equal to the 
-  //       width set in begin() or setAddressWidth()
-  //       methods (5 by default)
-  Serial.print(F("[nRF24] Setting address for receive pipe 0 ... "));
-  byte receiveAddr0[] = {0x05, 0x06, 0x07, 0x08, 0x09};
-  state = nrf.setReceivePipe(0, receiveAddr0);
-  if(state == ERR_NONE) {
-    Serial.println(F("success!"));
-  } else {
-    Serial.print(F("failed, code "));
-    Serial.println(state);
-    while(true);
-  }
-  
-  // set receive pipe 1 - 5 address
-  // NOTE: unlike receive pipe 0, pipes 1 - 5 are only
-  //       distinguished by their least significant byte,
-  //       the upper bytes will be the same!
-  Serial.print(F("[nRF24] Setting addresses for receive pipes 1 - 5 ... "));
-  byte receiveAddr1[] = {0xAA, 0xBB, 0xCC, 0xDD, 0xE1};
-  // set pipe 1 address
-  state = nrf.setReceivePipe(1, receiveAddr1);
-  // set the addresses for rest of pipes
-  state |= nrf.setReceivePipe(2, 0xE2);
-  state |= nrf.setReceivePipe(3, 0xE3);
-  state |= nrf.setReceivePipe(4, 0xE4);
-  state |= nrf.setReceivePipe(5, 0xE5);
-  if(state == ERR_NONE) {
-    Serial.println(F("success!"));
-  } else {
-    Serial.print(F("failed, code "));
-    Serial.println(state);
-    while(true);
-  }
-
-  // pipes 1 - 5 are automatically enabled upon address
-  // change, but can be disabled manually
-  Serial.print(F("[nRF24] Disabling pipes 2 - 5 ... "));
-  state = nrf.disablePipe(2);
-  if(state == ERR_NONE) {
-    Serial.println(F("success!"));
-  } else {
-    Serial.print(F("failed, code "));
-    Serial.println(state);
-    while(true);
-  }
-}
-
-void loop() {
-  Serial.print(F("[nRF24] Transmitting packet ... "));
-
-  // set transmit address
-  // NOTE: address width in bytes MUST be equal to the 
-  //       width set in begin() or setAddressWidth()
-  //       methods (5 by default)
-  byte addr[] = {0x00, 0x01, 0x02, 0x03, 0x04};
-
-  // you can transmit C-string or Arduino string up to
-  // 32 characters long
-  int state = nrf.transmit("Hello World!", addr);
-
-  if (state == ERR_NONE) {
-    // the packet was successfully transmitted
-    Serial.println(" success!");
-
-  } else if (state == ERR_PACKET_TOO_LONG) {
-    // the supplied packet was longer than 256 bytes
-    Serial.println(" too long!");
-
-  }
-
-  // wait for a second before transmitting again
-  delay(1000);
-}